Linux Box booted up, but no networking. Frustrated......
First check the following tools:
bash-3.2# ls /sbin/arp
/sbin/arp
bash-3.2# ls /sbin/ifconfig
/sbin/ifconfig
bash-3.2# ls /sbin/route
/sbin/route
What's the output:
bash-3.2# ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.255.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
bash-3.2# arp -a
bash-3.2# route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
bash-3.2#
Nothing useful...........; Try the following commands:
bash-3.2# ifconfig eth0 192.168.70.245 netmask 255.255.248.0 up
bash-3.2# route add default gw 192.168.64.1
bash-3.2# ifconfig
eth0 Link encap:Ethernet HWaddr 00:A0:C9:00:00:02
inet addr:192.168.70.245 Bcast:192.168.71.255 Mask:255.255.248.0
inet6 addr: fe80::2a0:c9ff:fe00:2/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:390 (390.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.255.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
bash-3.2# ping 192.168.66.157
PING 192.168.66.157 (192.168.66.157) 56(84) bytes of data.
64 bytes from 192.168.66.157: icmp_seq=1 ttl=64 time=10.1 ms
64 bytes from 192.168.66.157: icmp_seq=2 ttl=64 time=0.292 ms
64 bytes from 192.168.66.157: icmp_seq=3 ttl=64 time=0.288 ms
64 bytes from 192.168.66.157: icmp_seq=4 ttl=64 time=0.287 ms
^C
--- 192.168.66.157 ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 3008ms
rtt min/avg/max/mdev = 0.287/2.753/10.145/4.267 ms
bash-3.2# arp
Address HWtype HWaddress Flags Mask Iface
192.168.66.157 ether 00:0e:1e:0b:18:c0 C eth0
bash-3.2# route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.64.0 0.0.0.0 255.255.248.0 U 0 0 0 eth0
0.0.0.0 192.168.64.1 0.0.0.0 UG 0 0 0 eth0
bash-3.2# ifconfig
eth0 Link encap:Ethernet HWaddr 00:A0:C9:00:00:02
inet addr:192.168.70.245 Bcast:192.168.71.255 Mask:255.255.248.0
inet6 addr: fe80::2a0:c9ff:fe00:2/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1044 errors:0 dropped:0 overruns:0 frame:0
TX packets:11 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:141103 (137.7 KiB) TX bytes:866 (866.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.255.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:344 (344.0 b) TX bytes:344 (344.0 b)
So packet is flowing now.
Commands for reference:
Friday, August 30, 2013
Linux Domain Name Lookup Command
For DNS concept, see the wiki link
# nslookup google.com
Server: 171.70.168.183
Address: 171.70.168.183#53
Non-authoritative answer:
Name: google.com
Address: 74.125.239.131
Name: google.com
Address: 74.125.239.132
Name: google.com
Address: 74.125.239.135
Name: google.com
Address: 74.125.239.142
Name: google.com
Address: 74.125.239.136
Name: google.com
Address: 74.125.239.129
Name: google.com
Address: 74.125.239.130
Name: google.com
Address: 74.125.239.134
Name: google.com
Address: 74.125.239.128
Name: google.com
Address: 74.125.239.137
Name: google.com
Address: 74.125.239.133
See wiki for an high level view.
http://en.wikipedia.org/wiki/Nslookup
; <<>> DiG 9.2.4 <<>> google.com
;; global options: printcmd
;; Got answer:
;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 58279
;; flags: qr rd ra; QUERY: 1, ANSWER: 11, AUTHORITY: 4, ADDITIONAL: 4
;; QUESTION SECTION:
;google.com. IN A
;; ANSWER SECTION:
google.com. 172 IN A 74.125.239.142
google.com. 172 IN A 74.125.239.137
google.com. 172 IN A 74.125.239.133
google.com. 172 IN A 74.125.239.132
google.com. 172 IN A 74.125.239.130
google.com. 172 IN A 74.125.239.129
google.com. 172 IN A 74.125.239.135
google.com. 172 IN A 74.125.239.131
google.com. 172 IN A 74.125.239.134
google.com. 172 IN A 74.125.239.128
google.com. 172 IN A 74.125.239.136
;; AUTHORITY SECTION:
google.com. 96903 IN NS ns2.google.com.
google.com. 96903 IN NS ns1.google.com.
google.com. 96903 IN NS ns3.google.com.
google.com. 96903 IN NS ns4.google.com.
;; ADDITIONAL SECTION:
ns1.google.com. 271309 IN A 216.239.32.10
ns2.google.com. 239136 IN A 216.239.34.10
ns3.google.com. 274650 IN A 216.239.36.10
ns4.google.com. 273632 IN A 216.239.38.10
;; Query time: 5 msec
;; SERVER: 171.70.168.183#53(171.70.168.183)
;; WHEN: Fri Aug 30 12:56:23 2013
;; MSG SIZE rcvd: 340
# /usr/bin/host www.google.com
www.google.com has address 74.125.28.147
www.google.com has address 74.125.28.104
www.google.com has address 74.125.28.106
www.google.com has address 74.125.28.103
www.google.com has address 74.125.28.105
www.google.com has address 74.125.28.99
Here is one good article about those 3 tools.
http://blog.smalleycreative.com/linux/nslookup-is-dead-long-live-dig-and-host/
What happened if meeting the following issues:
bash-3.2# nslookup google.com
;; connection timed out; no servers could be reached
;; connection timed out; no servers could be reached
Check your configure file:
bash-3.2# cat /etc/resolv.conf
It is empty, so that is why :))
To solve the problem, do following configuration:
bash-3.2# cat /etc/resolv.conf
search comcast.com
nameserver 1.2.3.4
nameserver 4.3.2.1
search comcast.com
nameserver 1.2.3.4
nameserver 4.3.2.1
Dmesg related to x86 ACPI
[ 0.000000] BIOS-e820: 00000000bf77f000 - 00000000bf7cf000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000bf7cf000 - 00000000bf7ff000 (ACPI data)
Thursday, August 22, 2013
mpstat
# mpstat -P ALL
Linux 2.6.18-238.el5 08/22/2013
10:28:08 PM CPU %user %nice %sys %iowait %irq %soft %steal %idle intr/s
10:28:08 PM all 0.31 0.00 0.38 0.01 0.00 0.00 0.00 99.29 1216.28
10:28:08 PM 0 0.23 0.00 0.48 0.19 0.00 0.01 0.00 99.09 1005.54
10:28:08 PM 1 0.31 0.00 0.44 0.00 0.01 0.00 0.00 99.23 11.62
10:28:08 PM 2 0.20 0.00 0.38 0.01 0.00 0.00 0.00 99.40 4.30
10:28:08 PM 3 0.21 0.00 0.37 0.01 0.00 0.00 0.00 99.42 2.76
10:28:08 PM 4 0.21 0.00 0.36 0.00 0.00 0.00 0.00 99.42 1.37
10:28:08 PM 5 0.22 0.00 0.34 0.00 0.00 0.00 0.00 99.44 0.50
10:28:08 PM 6 0.23 0.00 0.35 0.01 0.00 0.00 0.00 99.41 2.29
10:28:08 PM 7 0.27 0.00 0.36 0.03 0.00 0.00 0.00 99.35 1.89
10:28:08 PM 8 0.21 0.00 0.49 0.06 0.00 0.01 0.00 99.23 3.52
10:28:08 PM 9 0.32 0.00 0.42 0.00 0.00 0.00 0.00 99.26 0.00
10:28:08 PM 10 0.19 0.00 0.38 0.00 0.00 0.00 0.00 99.44 0.00
10:28:08 PM 11 0.18 0.00 0.36 0.00 0.00 0.00 0.00 99.46 0.00
10:28:08 PM 12 0.17 0.00 0.36 0.00 0.00 0.00 0.00 99.47 0.05
10:28:08 PM 13 0.17 0.00 0.36 0.00 0.00 0.00 0.00 99.48 0.29
10:28:08 PM 14 0.19 0.00 0.36 0.00 0.00 0.00 0.00 99.45 0.00
10:28:08 PM 15 0.19 0.00 0.37 0.01 0.00 0.00 0.00 99.43 0.00
10:28:08 PM 16 0.22 0.00 0.46 0.05 0.00 0.01 0.00 99.26 2.68
10:28:08 PM 17 0.34 0.00 0.42 0.00 0.00 0.00 0.00 99.23 0.00
10:28:08 PM 18 0.18 0.00 0.37 0.00 0.00 0.00 0.00 99.44 0.00
10:28:08 PM 19 0.22 0.00 0.36 0.00 0.00 0.00 0.00 99.43 0.00
10:28:08 PM 20 0.18 0.00 0.36 0.00 0.00 0.00 0.00 99.46 0.01
10:28:08 PM 21 0.17 0.00 0.37 0.00 0.00 0.00 0.00 99.46 0.02
10:28:08 PM 22 0.19 0.00 0.37 0.01 0.00 0.00 0.00 99.44 0.00
10:28:08 PM 23 0.23 0.00 0.38 0.02 0.00 0.00 0.00 99.37 0.00
10:28:08 PM 24 0.19 0.00 0.43 0.03 0.00 0.00 0.00 99.34 1.21
10:28:08 PM 25 0.29 0.00 0.39 0.00 0.00 0.00 0.00 99.33 0.00
10:28:08 PM 26 0.17 0.00 0.34 0.00 0.00 0.00 0.00 99.49 0.00
10:28:08 PM 27 0.17 0.00 0.33 0.00 0.00 0.00 0.00 99.50 0.00
10:28:08 PM 28 0.17 0.00 0.33 0.00 0.00 0.00 0.00 99.50 0.00
10:28:08 PM 29 0.19 0.00 0.33 0.00 0.00 0.00 0.00 99.47 0.00
10:28:08 PM 30 0.20 0.00 0.33 0.00 0.00 0.00 0.00 99.46 0.00
10:28:08 PM 31 0.27 0.00 0.37 0.01 0.00 0.00 0.00 99.35 0.00
10:28:08 PM 32 0.28 0.00 0.39 0.01 0.00 0.00 0.00 99.33 0.00
10:28:08 PM 33 0.91 0.00 0.59 0.01 0.00 0.00 0.00 98.49 0.18
10:28:08 PM 34 0.33 0.00 0.39 0.01 0.00 0.00 0.00 99.28 1.86
10:28:08 PM 35 0.32 0.00 0.36 0.01 0.00 0.00 0.00 99.30 3.71
10:28:08 PM 36 0.33 0.00 0.36 0.00 0.00 0.00 0.00 99.30 4.70
10:28:08 PM 37 0.38 0.00 0.32 0.01 0.00 0.00 0.00 99.28 7.50
10:28:08 PM 38 0.52 0.00 0.34 0.01 0.00 0.01 0.00 99.12 13.40
10:28:08 PM 39 0.58 0.00 0.37 0.07 0.00 0.01 0.00 98.97 18.27
10:28:08 PM 40 0.29 0.00 0.35 0.01 0.00 0.00 0.00 99.35 0.00
10:28:08 PM 41 0.93 0.00 0.60 0.01 0.00 0.00 0.00 98.46 0.00
10:28:08 PM 42 0.32 0.00 0.37 0.00 0.00 0.00 0.00 99.31 0.00
10:28:08 PM 43 0.27 0.00 0.34 0.00 0.00 0.00 0.00 99.39 0.00
10:28:08 PM 44 0.25 0.00 0.33 0.00 0.00 0.00 0.00 99.42 0.00
10:28:08 PM 45 0.25 0.00 0.33 0.00 0.00 0.00 0.00 99.42 0.00
10:28:08 PM 46 0.32 0.00 0.34 0.00 0.00 0.01 0.00 99.33 8.27
10:28:08 PM 47 0.36 0.00 0.36 0.01 0.00 0.01 0.00 99.26 7.64
10:28:08 PM 48 0.25 0.00 0.36 0.00 0.00 0.00 0.00 99.39 0.00
10:28:08 PM 49 1.04 0.00 0.61 0.01 0.00 0.00 0.00 98.35 0.00
10:28:08 PM 50 0.31 0.00 0.36 0.00 0.00 0.00 0.00 99.32 0.00
10:28:08 PM 51 0.35 0.00 0.34 0.00 0.00 0.00 0.00 99.31 0.00
10:28:08 PM 52 0.26 0.00 0.34 0.00 0.00 0.00 0.00 99.40 0.00
10:28:08 PM 53 0.28 0.00 0.35 0.00 0.00 0.00 0.00 99.37 0.00
10:28:08 PM 54 0.29 0.00 0.34 0.00 0.00 0.00 0.00 99.37 1.09
10:28:08 PM 55 0.52 0.00 0.40 0.01 0.00 0.02 0.00 99.04 25.70
10:28:08 PM 56 0.24 0.00 0.33 0.00 0.00 0.00 0.00 99.42 0.00
10:28:08 PM 57 0.84 0.00 0.56 0.01 0.00 0.00 0.00 98.59 0.00
10:28:08 PM 58 0.30 0.00 0.33 0.00 0.00 0.00 0.00 99.36 0.00
10:28:08 PM 59 0.27 0.00 0.32 0.00 0.00 0.00 0.00 99.41 0.00
10:28:08 PM 60 0.27 0.00 0.31 0.00 0.00 0.00 0.00 99.42 0.00
10:28:08 PM 61 0.28 0.00 0.32 0.00 0.00 0.00 0.00 99.40 0.00
10:28:08 PM 62 0.31 0.00 0.31 0.00 0.00 0.00 0.00 99.39 0.06
10:28:08 PM 63 0.73 0.00 0.44 0.02 0.01 0.06 0.00 98.74 85.81
Linux 2.6.18-238.el5 08/22/2013
10:28:08 PM CPU %user %nice %sys %iowait %irq %soft %steal %idle intr/s
10:28:08 PM all 0.31 0.00 0.38 0.01 0.00 0.00 0.00 99.29 1216.28
10:28:08 PM 0 0.23 0.00 0.48 0.19 0.00 0.01 0.00 99.09 1005.54
10:28:08 PM 1 0.31 0.00 0.44 0.00 0.01 0.00 0.00 99.23 11.62
10:28:08 PM 2 0.20 0.00 0.38 0.01 0.00 0.00 0.00 99.40 4.30
10:28:08 PM 3 0.21 0.00 0.37 0.01 0.00 0.00 0.00 99.42 2.76
10:28:08 PM 4 0.21 0.00 0.36 0.00 0.00 0.00 0.00 99.42 1.37
10:28:08 PM 5 0.22 0.00 0.34 0.00 0.00 0.00 0.00 99.44 0.50
10:28:08 PM 6 0.23 0.00 0.35 0.01 0.00 0.00 0.00 99.41 2.29
10:28:08 PM 7 0.27 0.00 0.36 0.03 0.00 0.00 0.00 99.35 1.89
10:28:08 PM 8 0.21 0.00 0.49 0.06 0.00 0.01 0.00 99.23 3.52
10:28:08 PM 9 0.32 0.00 0.42 0.00 0.00 0.00 0.00 99.26 0.00
10:28:08 PM 10 0.19 0.00 0.38 0.00 0.00 0.00 0.00 99.44 0.00
10:28:08 PM 11 0.18 0.00 0.36 0.00 0.00 0.00 0.00 99.46 0.00
10:28:08 PM 12 0.17 0.00 0.36 0.00 0.00 0.00 0.00 99.47 0.05
10:28:08 PM 13 0.17 0.00 0.36 0.00 0.00 0.00 0.00 99.48 0.29
10:28:08 PM 14 0.19 0.00 0.36 0.00 0.00 0.00 0.00 99.45 0.00
10:28:08 PM 15 0.19 0.00 0.37 0.01 0.00 0.00 0.00 99.43 0.00
10:28:08 PM 16 0.22 0.00 0.46 0.05 0.00 0.01 0.00 99.26 2.68
10:28:08 PM 17 0.34 0.00 0.42 0.00 0.00 0.00 0.00 99.23 0.00
10:28:08 PM 18 0.18 0.00 0.37 0.00 0.00 0.00 0.00 99.44 0.00
10:28:08 PM 19 0.22 0.00 0.36 0.00 0.00 0.00 0.00 99.43 0.00
10:28:08 PM 20 0.18 0.00 0.36 0.00 0.00 0.00 0.00 99.46 0.01
10:28:08 PM 21 0.17 0.00 0.37 0.00 0.00 0.00 0.00 99.46 0.02
10:28:08 PM 22 0.19 0.00 0.37 0.01 0.00 0.00 0.00 99.44 0.00
10:28:08 PM 23 0.23 0.00 0.38 0.02 0.00 0.00 0.00 99.37 0.00
10:28:08 PM 24 0.19 0.00 0.43 0.03 0.00 0.00 0.00 99.34 1.21
10:28:08 PM 25 0.29 0.00 0.39 0.00 0.00 0.00 0.00 99.33 0.00
10:28:08 PM 26 0.17 0.00 0.34 0.00 0.00 0.00 0.00 99.49 0.00
10:28:08 PM 27 0.17 0.00 0.33 0.00 0.00 0.00 0.00 99.50 0.00
10:28:08 PM 28 0.17 0.00 0.33 0.00 0.00 0.00 0.00 99.50 0.00
10:28:08 PM 29 0.19 0.00 0.33 0.00 0.00 0.00 0.00 99.47 0.00
10:28:08 PM 30 0.20 0.00 0.33 0.00 0.00 0.00 0.00 99.46 0.00
10:28:08 PM 31 0.27 0.00 0.37 0.01 0.00 0.00 0.00 99.35 0.00
10:28:08 PM 32 0.28 0.00 0.39 0.01 0.00 0.00 0.00 99.33 0.00
10:28:08 PM 33 0.91 0.00 0.59 0.01 0.00 0.00 0.00 98.49 0.18
10:28:08 PM 34 0.33 0.00 0.39 0.01 0.00 0.00 0.00 99.28 1.86
10:28:08 PM 35 0.32 0.00 0.36 0.01 0.00 0.00 0.00 99.30 3.71
10:28:08 PM 36 0.33 0.00 0.36 0.00 0.00 0.00 0.00 99.30 4.70
10:28:08 PM 37 0.38 0.00 0.32 0.01 0.00 0.00 0.00 99.28 7.50
10:28:08 PM 38 0.52 0.00 0.34 0.01 0.00 0.01 0.00 99.12 13.40
10:28:08 PM 39 0.58 0.00 0.37 0.07 0.00 0.01 0.00 98.97 18.27
10:28:08 PM 40 0.29 0.00 0.35 0.01 0.00 0.00 0.00 99.35 0.00
10:28:08 PM 41 0.93 0.00 0.60 0.01 0.00 0.00 0.00 98.46 0.00
10:28:08 PM 42 0.32 0.00 0.37 0.00 0.00 0.00 0.00 99.31 0.00
10:28:08 PM 43 0.27 0.00 0.34 0.00 0.00 0.00 0.00 99.39 0.00
10:28:08 PM 44 0.25 0.00 0.33 0.00 0.00 0.00 0.00 99.42 0.00
10:28:08 PM 45 0.25 0.00 0.33 0.00 0.00 0.00 0.00 99.42 0.00
10:28:08 PM 46 0.32 0.00 0.34 0.00 0.00 0.01 0.00 99.33 8.27
10:28:08 PM 47 0.36 0.00 0.36 0.01 0.00 0.01 0.00 99.26 7.64
10:28:08 PM 48 0.25 0.00 0.36 0.00 0.00 0.00 0.00 99.39 0.00
10:28:08 PM 49 1.04 0.00 0.61 0.01 0.00 0.00 0.00 98.35 0.00
10:28:08 PM 50 0.31 0.00 0.36 0.00 0.00 0.00 0.00 99.32 0.00
10:28:08 PM 51 0.35 0.00 0.34 0.00 0.00 0.00 0.00 99.31 0.00
10:28:08 PM 52 0.26 0.00 0.34 0.00 0.00 0.00 0.00 99.40 0.00
10:28:08 PM 53 0.28 0.00 0.35 0.00 0.00 0.00 0.00 99.37 0.00
10:28:08 PM 54 0.29 0.00 0.34 0.00 0.00 0.00 0.00 99.37 1.09
10:28:08 PM 55 0.52 0.00 0.40 0.01 0.00 0.02 0.00 99.04 25.70
10:28:08 PM 56 0.24 0.00 0.33 0.00 0.00 0.00 0.00 99.42 0.00
10:28:08 PM 57 0.84 0.00 0.56 0.01 0.00 0.00 0.00 98.59 0.00
10:28:08 PM 58 0.30 0.00 0.33 0.00 0.00 0.00 0.00 99.36 0.00
10:28:08 PM 59 0.27 0.00 0.32 0.00 0.00 0.00 0.00 99.41 0.00
10:28:08 PM 60 0.27 0.00 0.31 0.00 0.00 0.00 0.00 99.42 0.00
10:28:08 PM 61 0.28 0.00 0.32 0.00 0.00 0.00 0.00 99.40 0.00
10:28:08 PM 62 0.31 0.00 0.31 0.00 0.00 0.00 0.00 99.39 0.06
10:28:08 PM 63 0.73 0.00 0.44 0.02 0.01 0.06 0.00 98.74 85.81
Tuesday, August 20, 2013
X86 vs PowerPC watchdog
Registering platform device 'fsl-watchdog.1'. Parent at platform
watchdog-83xx: registered miscdev on minor=130 (err=0)
mpc83xx watchdog: control register 0xffff0007
mpc83xx watchdog: uBoot enabled watchdog
mpc83xx watchdog: timer installed
X86 vs PowerPC I2C
Registering platform device 'fsl-i2c.1'. Parent at platform
Registering platform device 'fsl-i2c.2'. Parent at platform
i2c /dev entries driver
OBFL: i2c-mpc1 - attached interrupt 14
OBFL: i2c-mpc2 - attached interrupt 15
X86 vs PowerPC Serial port
On X86:
[ 3.162453] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 3.443900] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
On PowerPC:
Registering platform device 'serial8250.0'. Parent at platform
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
Registering platform device 'serial8250'. Parent at platform
ttyS0 at MMIO 0xe0004500 (irq = 9) is a 16550A
ttyS1 at MMIO 0xe0004600 (irq = 9) is a 16550A
ttyS0 at MMIO 0xe0004500 (irq = 9) is a 16550A
ttyS1 at MMIO 0xe0004600 (irq = 10) is a 16550A
[ 3.162453] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 3.443900] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
On PowerPC:
Registering platform device 'serial8250.0'. Parent at platform
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
Registering platform device 'serial8250'. Parent at platform
ttyS0 at MMIO 0xe0004500 (irq = 9) is a 16550A
ttyS1 at MMIO 0xe0004600 (irq = 9) is a 16550A
ttyS0 at MMIO 0xe0004500 (irq = 9) is a 16550A
ttyS1 at MMIO 0xe0004600 (irq = 10) is a 16550A
Linux Dmesg on X86 server
Linux version 2.6.18-238.el5 (mockbuild@x86-012.build.bos.redhat.com) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-50)) #1 SMP Sun Dec 19 14:22:44 EST 2010
Command line: ro root=LABEL=/ rhgb quiet
BIOS-provided physical RAM map:
BIOS-e820: 0000000000010000 - 000000000009ec00 (usable)
BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007e59b000 (usable)
BIOS-e820: 000000007e59b000 - 000000007e617000 (ACPI data)
BIOS-e820: 000000007e617000 - 000000007f469000 (reserved)
BIOS-e820: 000000007f469000 - 000000007f471000 (ACPI NVS)
BIOS-e820: 000000007f471000 - 000000007f499000 (reserved)
BIOS-e820: 000000007f499000 - 000000007f800000 (ACPI NVS)
BIOS-e820: 0000000080000000 - 0000000090000000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed40000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000006880000000 (usable)
DMI 2.7 present.
ACPI: RSDP (v002 Cisco ) @ 0x00000000000f0490
ACPI: XSDT (v001 Cisco CiscoUCS 0x00000000 AMI 0x00010013) @ 0x000000007e59b090
ACPI: FADT (v004 Cisco CiscoUCS 0x00000000 AMI 0x00010013) @ 0x000000007e5a4ee0
ACPI: MADT (v003 Cisco CiscoUCS 0x00000000 AMI 0x00010013) @ 0x000000007e5a4fd8
ACPI: MCFG (v001 Cisco CiscoUCS 0x00000000 MSFT 0x00000097) @ 0x000000007e5a5260
ACPI: PRAD (v002 Cisco CiscoUCS 0x00000001 MSFT 0x03000001) @ 0x000000007e5a52a0
ACPI: SLIC (v001 Cisco CiscoUCS 0x00000000 AMI 0x00010013) @ 0x000000007e5a5360
ACPI: SRAT (v003 Cisco CiscoUCS 0x00000001 AMI. 0x00000000) @ 0x000000007e5a54d8
ACPI: SLIT (v001 Cisco CiscoUCS 0x00000000 AMI. 0x00000000) @ 0x000000007e5a5e08
ACPI: HPET (v001 Cisco CiscoUCS 0x00000000 AMI. 0x00000004) @ 0x000000007e5a5e48
ACPI: SPMI (v005 Cisco CiscoUCS 0x00000000 AMI. 0x00000000) @ 0x000000007e5a5e80
ACPI: SSDT (v002 Cisco CiscoUCS 0x00004000 INTL 0x20051117) @ 0x000000007e5a5ec0
ACPI: SPCR (v001 Cisco CiscoUCS 0x00000000 AMI. 0x00000004) @ 0x000000007e615fc8
ACPI: DMAR (v001 Cisco CiscoUCS 0x00000001 INTL 0x00000001) @ 0x000000007e616018
ACPI: EINJ (v001 Cisco CiscoUCS 0x00000000 0x00000000) @ 0x000000007e6161a8
ACPI: ERST (v001 Cisco CiscoUCS 0x00000000 0x00000000) @ 0x000000007e6162d8
ACPI: HEST (v001 Cisco CiscoUCS 0x00000000 0x00000000) @ 0x000000007e6164e8
ACPI: BERT (v001 Cisco CiscoUCS 0x00000000 0x00000000) @ 0x000000007e616590
ACPI: DSDT (v002 Cisco CiscoUCS 0x00000000 INTL 0x20091112) @ 0x0000000000000000
SRAT: PXM 0 -> APIC 0 -> Node 0
SRAT: PXM 0 -> APIC 1 -> Node 0
SRAT: PXM 0 -> APIC 2 -> Node 0
SRAT: PXM 0 -> APIC 3 -> Node 0
SRAT: PXM 0 -> APIC 4 -> Node 0
SRAT: PXM 0 -> APIC 5 -> Node 0
SRAT: PXM 0 -> APIC 6 -> Node 0
SRAT: PXM 0 -> APIC 7 -> Node 0
SRAT: PXM 0 -> APIC 8 -> Node 0
SRAT: PXM 0 -> APIC 9 -> Node 0
SRAT: PXM 0 -> APIC 10 -> Node 0
SRAT: PXM 0 -> APIC 11 -> Node 0
SRAT: PXM 0 -> APIC 12 -> Node 0
SRAT: PXM 0 -> APIC 13 -> Node 0
SRAT: PXM 0 -> APIC 14 -> Node 0
SRAT: PXM 0 -> APIC 15 -> Node 0
SRAT: PXM 1 -> APIC 32 -> Node 1
SRAT: PXM 1 -> APIC 33 -> Node 1
SRAT: PXM 1 -> APIC 34 -> Node 1
SRAT: PXM 1 -> APIC 35 -> Node 1
SRAT: PXM 1 -> APIC 36 -> Node 1
SRAT: PXM 1 -> APIC 37 -> Node 1
SRAT: PXM 1 -> APIC 38 -> Node 1
SRAT: PXM 1 -> APIC 39 -> Node 1
SRAT: PXM 1 -> APIC 40 -> Node 1
SRAT: PXM 1 -> APIC 41 -> Node 1
SRAT: PXM 1 -> APIC 42 -> Node 1
SRAT: PXM 1 -> APIC 43 -> Node 1
SRAT: PXM 1 -> APIC 44 -> Node 1
SRAT: PXM 1 -> APIC 45 -> Node 1
SRAT: PXM 1 -> APIC 46 -> Node 1
SRAT: PXM 1 -> APIC 47 -> Node 1
SRAT: PXM 2 -> APIC 64 -> Node 2
SRAT: PXM 2 -> APIC 65 -> Node 2
SRAT: PXM 2 -> APIC 66 -> Node 2
SRAT: PXM 2 -> APIC 67 -> Node 2
SRAT: PXM 2 -> APIC 68 -> Node 2
SRAT: PXM 2 -> APIC 69 -> Node 2
SRAT: PXM 2 -> APIC 70 -> Node 2
SRAT: PXM 2 -> APIC 71 -> Node 2
SRAT: PXM 2 -> APIC 72 -> Node 2
SRAT: PXM 2 -> APIC 73 -> Node 2
SRAT: PXM 2 -> APIC 74 -> Node 2
SRAT: PXM 2 -> APIC 75 -> Node 2
SRAT: PXM 2 -> APIC 76 -> Node 2
SRAT: PXM 2 -> APIC 77 -> Node 2
SRAT: PXM 2 -> APIC 78 -> Node 2
SRAT: PXM 2 -> APIC 79 -> Node 2
SRAT: PXM 3 -> APIC 96 -> Node 3
SRAT: PXM 3 -> APIC 97 -> Node 3
SRAT: PXM 3 -> APIC 98 -> Node 3
SRAT: PXM 3 -> APIC 99 -> Node 3
SRAT: PXM 3 -> APIC 100 -> Node 3
SRAT: PXM 3 -> APIC 101 -> Node 3
SRAT: PXM 3 -> APIC 102 -> Node 3
SRAT: PXM 3 -> APIC 103 -> Node 3
SRAT: PXM 3 -> APIC 104 -> Node 3
SRAT: PXM 3 -> APIC 105 -> Node 3
SRAT: PXM 3 -> APIC 106 -> Node 3
SRAT: PXM 3 -> APIC 107 -> Node 3
SRAT: PXM 3 -> APIC 108 -> Node 3
SRAT: PXM 3 -> APIC 109 -> Node 3
SRAT: PXM 3 -> APIC 110 -> Node 3
SRAT: PXM 3 -> APIC 111 -> Node 3
SRAT: Node 0 PXM 0 0-80000000
SRAT: Node 0 PXM 0 0-2080000000
SRAT: Node 1 PXM 1 2080000000-3880000000
SRAT: Node 2 PXM 2 3880000000-5080000000
SRAT: Node 3 PXM 3 5080000000-6880000000
NUMA: Using 31 for the hash shift.
Bootmem setup node 0 0000000000000000-0000002080000000
Bootmem setup node 1 0000002080000000-0000003880000000
Bootmem setup node 2 0000003880000000-0000005080000000
Bootmem setup node 3 0000005080000000-0000006880000000
Memory for crash kernel (0x0 to 0x0) notwithin permissible range
disabling kdump
On node 0 totalpages: 33079737
DMA zone: 2022 pages, LIFO batch:0
DMA32 zone: 499155 pages, LIFO batch:31
Normal zone: 32578560 pages, LIFO batch:31
On node 1 totalpages: 24821760
Normal zone: 24821760 pages, LIFO batch:31
On node 2 totalpages: 24821760
Normal zone: 24821760 pages, LIFO batch:31
On node 3 totalpages: 24821760
Normal zone: 24821760 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
Processor #2 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] enabled)
Processor #4 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] enabled)
Processor #6 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x08] enabled)
Processor #8 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x0a] enabled)
Processor #10 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x0c] enabled)
Processor #12 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x0e] enabled)
Processor #14 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x10] lapic_id[0x20] enabled)
Processor #32 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x12] lapic_id[0x22] enabled)
Processor #34 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x14] lapic_id[0x24] enabled)
Processor #36 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x16] lapic_id[0x26] enabled)
Processor #38 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x18] lapic_id[0x28] enabled)
Processor #40 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x1a] lapic_id[0x2a] enabled)
Processor #42 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x1c] lapic_id[0x2c] enabled)
Processor #44 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x1e] lapic_id[0x2e] enabled)
Processor #46 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x20] lapic_id[0x40] enabled)
Processor #64 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x22] lapic_id[0x42] enabled)
Processor #66 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x24] lapic_id[0x44] enabled)
Processor #68 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x26] lapic_id[0x46] enabled)
Processor #70 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x28] lapic_id[0x48] enabled)
Processor #72 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x2a] lapic_id[0x4a] enabled)
Processor #74 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x2c] lapic_id[0x4c] enabled)
Processor #76 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x2e] lapic_id[0x4e] enabled)
Processor #78 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x30] lapic_id[0x60] enabled)
Processor #96 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x32] lapic_id[0x62] enabled)
Processor #98 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x34] lapic_id[0x64] enabled)
Processor #100 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x36] lapic_id[0x66] enabled)
Processor #102 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x38] lapic_id[0x68] enabled)
Processor #104 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x3a] lapic_id[0x6a] enabled)
Processor #106 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x3c] lapic_id[0x6c] enabled)
Processor #108 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x3e] lapic_id[0x6e] enabled)
Processor #110 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
Processor #3 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x05] enabled)
Processor #5 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled)
Processor #7 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x09] lapic_id[0x09] enabled)
Processor #9 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x0b] enabled)
Processor #11 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x0d] enabled)
Processor #13 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x0f] enabled)
Processor #15 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x11] lapic_id[0x21] enabled)
Processor #33 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x13] lapic_id[0x23] enabled)
Processor #35 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x15] lapic_id[0x25] enabled)
Processor #37 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x17] lapic_id[0x27] enabled)
Processor #39 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x19] lapic_id[0x29] enabled)
Processor #41 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x1b] lapic_id[0x2b] enabled)
Processor #43 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x1d] lapic_id[0x2d] enabled)
Processor #45 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x1f] lapic_id[0x2f] enabled)
Processor #47 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x21] lapic_id[0x41] enabled)
Processor #65 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x23] lapic_id[0x43] enabled)
Processor #67 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x25] lapic_id[0x45] enabled)
Processor #69 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x27] lapic_id[0x47] enabled)
Processor #71 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x29] lapic_id[0x49] enabled)
Processor #73 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x2b] lapic_id[0x4b] enabled)
Processor #75 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x2d] lapic_id[0x4d] enabled)
Processor #77 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x2f] lapic_id[0x4f] enabled)
Processor #79 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x31] lapic_id[0x61] enabled)
Processor #97 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x33] lapic_id[0x63] enabled)
Processor #99 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x35] lapic_id[0x65] enabled)
Processor #101 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x37] lapic_id[0x67] enabled)
Processor #103 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x39] lapic_id[0x69] enabled)
Processor #105 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x3b] lapic_id[0x6b] enabled)
Processor #107 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x3d] lapic_id[0x6d] enabled)
Processor #109 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x3f] lapic_id[0x6f] enabled)
Processor #111 6:13 APIC version 21
ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x02] address[0xfec01000] gsi_base[24])
IOAPIC[1]: apic_id 2, version 32, address 0xfec01000, GSI 24-47
ACPI: IOAPIC (id[0x03] address[0xfec40000] gsi_base[48])
IOAPIC[2]: apic_id 3, version 32, address 0xfec40000, GSI 48-71
ACPI: IOAPIC (id[0x04] address[0xfec80000] gsi_base[72])
IOAPIC[3]: apic_id 4, version 32, address 0xfec80000, GSI 72-95
ACPI: IOAPIC (id[0x05] address[0xfecc0000] gsi_base[96])
IOAPIC[4]: apic_id 5, version 32, address 0xfecc0000, GSI 96-119
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to physical flat
ACPI: HPET id: 0x8086a701 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000009e000 - 000000000009f000
Nosave address range: 000000000009f000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 00000000000e0000
Nosave address range: 00000000000e0000 - 0000000000100000
Nosave address range: 000000007e59b000 - 000000007e617000
Nosave address range: 000000007e617000 - 000000007f469000
Nosave address range: 000000007f469000 - 000000007f471000
Nosave address range: 000000007f471000 - 000000007f499000
Nosave address range: 000000007f499000 - 000000007f800000
Nosave address range: 000000007f800000 - 0000000080000000
Nosave address range: 0000000080000000 - 0000000090000000
Nosave address range: 0000000090000000 - 00000000fed1c000
Nosave address range: 00000000fed1c000 - 00000000fed40000
Nosave address range: 00000000fed40000 - 00000000ff000000
Nosave address range: 00000000ff000000 - 0000000100000000
Allocating PCI resources starting at 98000000 (gap: 90000000:6ed1c000)
SMP: Allowing 64 CPUs, 0 hotplug CPUs
Built 4 zonelists. Total pages: 107545017
Kernel command line: ro root=LABEL=/ rhgb quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 67108864 (order: 17, 536870912 bytes)
Inode-cache hash table entries: 33554432 (order: 16, 268435456 bytes)
Checking aperture...
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing software IO TLB between 0x310a3000 - 0x350a3000
Memory: 429321636k/438304768k available (2592k kernel code, 6858496k reserved, 1649k data, 224k init)
Calibrating delay loop (skipped), value calculated using timer frequency.. 5400.22 BogoMIPS (lpj=2700112)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 0/0 -> Node 0
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM1)
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
Using local APIC timer interrupts.
Detected 6.250 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/64 APIC 0x2
Initializing CPU#1
Calibrating delay using timer specific routine.. 5399.99 BogoMIPS (lpj=2699996)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 1/2 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 2/64 APIC 0x4
Initializing CPU#2
Calibrating delay using timer specific routine.. 5399.84 BogoMIPS (lpj=2699924)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 2/4 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
CPU2: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 3/64 APIC 0x6
Initializing CPU#3
Calibrating delay using timer specific routine.. 5400.00 BogoMIPS (lpj=2700003)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 3/6 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 3
CPU3: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 4/64 APIC 0x8
Initializing CPU#4
Calibrating delay using timer specific routine.. 5399.92 BogoMIPS (lpj=2699962)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 4/8 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 4
CPU4: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 5/64 APIC 0xa
Initializing CPU#5
Calibrating delay using timer specific routine.. 5399.92 BogoMIPS (lpj=2699963)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 5/a -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 5
CPU5: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 6/64 APIC 0xc
Initializing CPU#6
Calibrating delay using timer specific routine.. 5399.92 BogoMIPS (lpj=2699963)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 6/c -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 6
CPU6: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 7/64 APIC 0xe
Initializing CPU#7
Calibrating delay using timer specific routine.. 5400.00 BogoMIPS (lpj=2700004)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 7/e -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 7
CPU7: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 8/64 APIC 0x20
Initializing CPU#8
Calibrating delay using timer specific routine.. 5400.11 BogoMIPS (lpj=2700059)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 8/20 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 0
CPU8: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 9/64 APIC 0x22
Initializing CPU#9
Calibrating delay using timer specific routine.. 5400.03 BogoMIPS (lpj=2700018)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 9/22 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 1
CPU9: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 10/64 APIC 0x24
Initializing CPU#10
Calibrating delay using timer specific routine.. 5400.11 BogoMIPS (lpj=2700056)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 10/24 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 2
CPU10: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 11/64 APIC 0x26
Initializing CPU#11
Calibrating delay using timer specific routine.. 5400.12 BogoMIPS (lpj=2700062)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 11/26 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 3
CPU11: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 12/64 APIC 0x28
Initializing CPU#12
Calibrating delay using timer specific routine.. 5400.01 BogoMIPS (lpj=2700006)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 12/28 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 4
CPU12: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 13/64 APIC 0x2a
Initializing CPU#13
Calibrating delay using timer specific routine.. 5400.16 BogoMIPS (lpj=2700081)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 13/2a -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 5
CPU13: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 14/64 APIC 0x2c
Initializing CPU#14
Calibrating delay using timer specific routine.. 5400.03 BogoMIPS (lpj=2700015)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 14/2c -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 6
CPU14: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 15/64 APIC 0x2e
Initializing CPU#15
Calibrating delay using timer specific routine.. 5400.13 BogoMIPS (lpj=2700066)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 15/2e -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 7
CPU15: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 16/64 APIC 0x40
Initializing CPU#16
Calibrating delay using timer specific routine.. 5400.05 BogoMIPS (lpj=2700025)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 16/40 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 0
CPU16: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 17/64 APIC 0x42
Initializing CPU#17
Calibrating delay using timer specific routine.. 5400.11 BogoMIPS (lpj=2700057)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 17/42 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 1
CPU17: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 18/64 APIC 0x44
Initializing CPU#18
Calibrating delay using timer specific routine.. 5400.08 BogoMIPS (lpj=2700042)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 18/44 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 2
CPU18: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 19/64 APIC 0x46
Initializing CPU#19
Calibrating delay using timer specific routine.. 5400.02 BogoMIPS (lpj=2700012)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 19/46 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 3
CPU19: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 20/64 APIC 0x48
Initializing CPU#20
Calibrating delay using timer specific routine.. 5400.10 BogoMIPS (lpj=2700051)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 20/48 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 4
CPU20: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 21/64 APIC 0x4a
Initializing CPU#21
Calibrating delay using timer specific routine.. 5400.01 BogoMIPS (lpj=2700005)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 21/4a -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 5
CPU21: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 22/64 APIC 0x4c
Initializing CPU#22
Calibrating delay using timer specific routine.. 5400.17 BogoMIPS (lpj=2700088)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 22/4c -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 6
CPU22: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 23/64 APIC 0x4e
Initializing CPU#23
Calibrating delay using timer specific routine.. 5399.94 BogoMIPS (lpj=2699970)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 23/4e -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 7
CPU23: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 24/64 APIC 0x60
Initializing CPU#24
Calibrating delay using timer specific routine.. 5400.21 BogoMIPS (lpj=2700109)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 24/60 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 0
CPU24: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 25/64 APIC 0x62
Initializing CPU#25
Calibrating delay using timer specific routine.. 5400.06 BogoMIPS (lpj=2700030)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 25/62 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 1
CPU25: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 26/64 APIC 0x64
Initializing CPU#26
Calibrating delay using timer specific routine.. 5400.14 BogoMIPS (lpj=2700070)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 26/64 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 2
CPU26: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 27/64 APIC 0x66
Initializing CPU#27
Calibrating delay using timer specific routine.. 5400.03 BogoMIPS (lpj=2700016)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 27/66 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 3
CPU27: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 28/64 APIC 0x68
Initializing CPU#28
Calibrating delay using timer specific routine.. 5400.12 BogoMIPS (lpj=2700064)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 28/68 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 4
CPU28: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 29/64 APIC 0x6a
Initializing CPU#29
Calibrating delay using timer specific routine.. 5400.05 BogoMIPS (lpj=2700026)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 29/6a -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 5
CPU29: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 30/64 APIC 0x6c
Initializing CPU#30
Calibrating delay using timer specific routine.. 5400.07 BogoMIPS (lpj=2700037)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 30/6c -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 6
CPU30: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 31/64 APIC 0x6e
Initializing CPU#31
Calibrating delay using timer specific routine.. 5400.02 BogoMIPS (lpj=2700013)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 31/6e -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 7
CPU31: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 32/64 APIC 0x1
Initializing CPU#32
Calibrating delay using timer specific routine.. 5400.05 BogoMIPS (lpj=2700027)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 32/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU32: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 33/64 APIC 0x3
Initializing CPU#33
Calibrating delay using timer specific routine.. 5400.13 BogoMIPS (lpj=2700067)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 33/3 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU33: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 34/64 APIC 0x5
Initializing CPU#34
Calibrating delay using timer specific routine.. 5400.10 BogoMIPS (lpj=2700052)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 34/5 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
CPU34: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 35/64 APIC 0x7
Initializing CPU#35
Calibrating delay using timer specific routine.. 5399.98 BogoMIPS (lpj=2699990)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 35/7 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 3
CPU35: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 36/64 APIC 0x9
Initializing CPU#36
Calibrating delay using timer specific routine.. 5400.13 BogoMIPS (lpj=2700067)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 36/9 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 4
CPU36: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 37/64 APIC 0xb
Initializing CPU#37
Calibrating delay using timer specific routine.. 5400.05 BogoMIPS (lpj=2700027)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 37/b -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 5
CPU37: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 38/64 APIC 0xd
Initializing CPU#38
Calibrating delay using timer specific routine.. 5400.13 BogoMIPS (lpj=2700069)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 38/d -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 6
CPU38: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 39/64 APIC 0xf
Initializing CPU#39
Calibrating delay using timer specific routine.. 5400.07 BogoMIPS (lpj=2700037)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 39/f -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 7
CPU39: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 40/64 APIC 0x21
Initializing CPU#40
Calibrating delay using timer specific routine.. 5400.20 BogoMIPS (lpj=2700104)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 40/21 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 0
CPU40: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 41/64 APIC 0x23
Initializing CPU#41
Calibrating delay using timer specific routine.. 5400.09 BogoMIPS (lpj=2700049)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 41/23 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 1
CPU41: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 42/64 APIC 0x25
Initializing CPU#42
Calibrating delay using timer specific routine.. 5400.07 BogoMIPS (lpj=2700037)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 42/25 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 2
CPU42: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 43/64 APIC 0x27
Initializing CPU#43
Calibrating delay using timer specific routine.. 5400.06 BogoMIPS (lpj=2700033)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 43/27 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 3
CPU43: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 44/64 APIC 0x29
Initializing CPU#44
Calibrating delay using timer specific routine.. 5400.20 BogoMIPS (lpj=2700101)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 44/29 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 4
CPU44: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 45/64 APIC 0x2b
Initializing CPU#45
Calibrating delay using timer specific routine.. 5400.15 BogoMIPS (lpj=2700075)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 45/2b -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 5
CPU45: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 46/64 APIC 0x2d
Initializing CPU#46
Calibrating delay using timer specific routine.. 5400.05 BogoMIPS (lpj=2700027)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 46/2d -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 6
CPU46: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 47/64 APIC 0x2f
Initializing CPU#47
Calibrating delay using timer specific routine.. 5400.03 BogoMIPS (lpj=2700017)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 47/2f -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 7
CPU47: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 48/64 APIC 0x41
Initializing CPU#48
Calibrating delay using timer specific routine.. 5400.00 BogoMIPS (lpj=2700000)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 48/41 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 0
CPU48: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 49/64 APIC 0x43
Initializing CPU#49
Calibrating delay using timer specific routine.. 5400.21 BogoMIPS (lpj=2700107)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 49/43 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 1
CPU49: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 50/64 APIC 0x45
Initializing CPU#50
Calibrating delay using timer specific routine.. 5400.11 BogoMIPS (lpj=2700056)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 50/45 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 2
CPU50: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 51/64 APIC 0x47
Initializing CPU#51
Calibrating delay using timer specific routine.. 5400.01 BogoMIPS (lpj=2700008)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 51/47 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 3
CPU51: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 52/64 APIC 0x49
Initializing CPU#52
Calibrating delay using timer specific routine.. 5400.02 BogoMIPS (lpj=2700010)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 52/49 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 4
CPU52: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 53/64 APIC 0x4b
Initializing CPU#53
Calibrating delay using timer specific routine.. 5400.01 BogoMIPS (lpj=2700007)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 53/4b -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 5
CPU53: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 54/64 APIC 0x4d
Initializing CPU#54
Calibrating delay using timer specific routine.. 5400.17 BogoMIPS (lpj=2700086)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 54/4d -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 6
CPU54: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 55/64 APIC 0x4f
Initializing CPU#55
Calibrating delay using timer specific routine.. 5400.09 BogoMIPS (lpj=2700049)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 55/4f -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 7
CPU55: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 56/64 APIC 0x61
Initializing CPU#56
Calibrating delay using timer specific routine.. 5400.05 BogoMIPS (lpj=2700028)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 56/61 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 0
CPU56: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 57/64 APIC 0x63
Initializing CPU#57
Calibrating delay using timer specific routine.. 5400.06 BogoMIPS (lpj=2700030)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 57/63 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 1
CPU57: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 58/64 APIC 0x65
Initializing CPU#58
Calibrating delay using timer specific routine.. 5400.06 BogoMIPS (lpj=2700031)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 58/65 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 2
CPU58: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 59/64 APIC 0x67
Initializing CPU#59
Calibrating delay using timer specific routine.. 5400.21 BogoMIPS (lpj=2700108)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 59/67 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 3
CPU59: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 60/64 APIC 0x69
Initializing CPU#60
Calibrating delay using timer specific routine.. 5400.13 BogoMIPS (lpj=2700065)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 60/69 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 4
CPU60: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 61/64 APIC 0x6b
Initializing CPU#61
Calibrating delay using timer specific routine.. 5400.25 BogoMIPS (lpj=2700126)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 61/6b -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 5
CPU61: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 62/64 APIC 0x6d
Initializing CPU#62
Calibrating delay using timer specific routine.. 5400.09 BogoMIPS (lpj=2700049)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 62/6d -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 6
CPU62: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 63/64 APIC 0x6f
Initializing CPU#63
Calibrating delay using timer specific routine.. 5400.05 BogoMIPS (lpj=2700027)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 63/6f -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 7
CPU63: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
Brought up 64 CPUs
CPU#0: NMI watchdog performance counter calibration - 4606->4626
CPU#1: NMI watchdog performance counter calibration - 68->88
CPU#2: NMI watchdog performance counter calibration - 68->88
CPU#3: NMI watchdog performance counter calibration - 66->86
CPU#4: NMI watchdog performance counter calibration - 66->86
CPU#5: NMI watchdog performance counter calibration - 66->86
CPU#6: NMI watchdog performance counter calibration - 66->86
CPU#7: NMI watchdog performance counter calibration - 66->86
CPU#8: NMI watchdog performance counter calibration - 67->87
CPU#9: NMI watchdog performance counter calibration - 67->87
CPU#10: NMI watchdog performance counter calibration - 67->87
CPU#11: NMI watchdog performance counter calibration - 66->86
CPU#12: NMI watchdog performance counter calibration - 67->87
CPU#13: NMI watchdog performance counter calibration - 66->86
CPU#14: NMI watchdog performance counter calibration - 66->86
CPU#15: NMI watchdog performance counter calibration - 65->85
CPU#16: NMI watchdog performance counter calibration - 65->85
CPU#17: NMI watchdog performance counter calibration - 65->85
CPU#18: NMI watchdog performance counter calibration - 65->85
CPU#19: NMI watchdog performance counter calibration - 65->85
CPU#20: NMI watchdog performance counter calibration - 65->85
CPU#21: NMI watchdog performance counter calibration - 65->85
CPU#22: NMI watchdog performance counter calibration - 65->85
CPU#23: NMI watchdog performance counter calibration - 65->85
CPU#24: NMI watchdog performance counter calibration - 65->85
CPU#25: NMI watchdog performance counter calibration - 65->85
CPU#26: NMI watchdog performance counter calibration - 65->85
CPU#27: NMI watchdog performance counter calibration - 64->84
CPU#28: NMI watchdog performance counter calibration - 64->84
CPU#29: NMI watchdog performance counter calibration - 64->84
CPU#30: NMI watchdog performance counter calibration - 64->84
CPU#31: NMI watchdog performance counter calibration - 64->84
CPU#32: NMI watchdog performance counter calibration - 64->84
CPU#33: NMI watchdog performance counter calibration - 64->84
CPU#34: NMI watchdog performance counter calibration - 63->83
CPU#35: NMI watchdog performance counter calibration - 62->83
CPU#36: NMI watchdog performance counter calibration - 62->82
CPU#37: NMI watchdog performance counter calibration - 62->82
CPU#38: NMI watchdog performance counter calibration - 62->82
CPU#39: NMI watchdog performance counter calibration - 62->82
CPU#40: NMI watchdog performance counter calibration - 63->83
CPU#41: NMI watchdog performance counter calibration - 63->83
CPU#42: NMI watchdog performance counter calibration - 63->83
CPU#43: NMI watchdog performance counter calibration - 63->83
CPU#44: NMI watchdog performance counter calibration - 63->83
CPU#45: NMI watchdog performance counter calibration - 62->83
CPU#46: NMI watchdog performance counter calibration - 62->82
CPU#47: NMI watchdog performance counter calibration - 62->82
CPU#48: NMI watchdog performance counter calibration - 62->82
CPU#49: NMI watchdog performance counter calibration - 62->82
CPU#50: NMI watchdog performance counter calibration - 62->82
CPU#51: NMI watchdog performance counter calibration - 62->82
CPU#52: NMI watchdog performance counter calibration - 62->82
CPU#53: NMI watchdog performance counter calibration - 62->82
CPU#54: NMI watchdog performance counter calibration - 61->81
CPU#55: NMI watchdog performance counter calibration - 61->81
CPU#56: NMI watchdog performance counter calibration - 62->82
CPU#57: NMI watchdog performance counter calibration - 62->82
CPU#58: NMI watchdog performance counter calibration - 62->82
CPU#59: NMI watchdog performance counter calibration - 61->81
CPU#60: NMI watchdog performance counter calibration - 61->81
CPU#61: NMI watchdog performance counter calibration - 61->81
CPU#62: NMI watchdog performance counter calibration - 61->81
CPU#63: NMI watchdog performance counter calibration - 61->81
NMI watchdog testing PASSED.
time.c: Using 14.318180 MHz WALL HPET GTOD HPET/TSC timer.
time.c: Detected 2700.112 MHz processor.
sizeof(vma)=176 bytes
sizeof(page)=56 bytes
sizeof(inode)=560 bytes
sizeof(dentry)=216 bytes
sizeof(ext3inode)=760 bytes
sizeof(buffer_head)=96 bytes
sizeof(skbuff)=248 bytes
migration_cost=3,34,2658
checking if image is initramfs... it is
Freeing initrd memory: 3090k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at 80000000
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:1e.0
bus 0 -> pxm 0 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX7._PRT]
ACPI: PCI Root Bridge [UNC0] (0000:3f)
ACPI: PCI Root Bridge [PCI1] (0000:40)
bus 64 -> pxm 1 -> node 1
ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT]
ACPI: PCI Root Bridge [UNC1] (0000:7f)
ACPI: PCI Root Bridge [PCI2] (0000:80)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI2._PRT]
ACPI: PCI Root Bridge [UNC2] (0000:bf)
ACPI: PCI Root Bridge [PCI3] (0000:c0)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI3._PRT]
ACPI: PCI Root Bridge [UNC3] (0000:ff)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 27 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000 (virtual 0xffffffffff5fe000), IRQs 2, 8, 0, 0, 0, 0, 0, 0
hpet0: 8 64-bit timers, 14318180 Hz
DMAR:Host address width 46
DMAR:DRHD base: 0x000000fbffe000 flags: 0x0
IOMMU fbffe000: ver 1:0 cap d2078c106f0462 ecap f020fe
DMAR:DRHD base: 0x000000e7ffe000 flags: 0x0
IOMMU e7ffe000: ver 1:0 cap d2078c106f0462 ecap f020fe
DMAR:DRHD base: 0x000000d3ffe000 flags: 0x0
IOMMU d3ffe000: ver 1:0 cap d2078c106f0462 ecap f020fe
DMAR:DRHD base: 0x000000bfffc000 flags: 0x1
IOMMU bfffc000: ver 1:0 cap d2078c106f0462 ecap f020fe
DMAR:RMRR base: 0x0000007f324000 end: 0x0000007f342fff
DMAR:ATSR flags: 0x0
DMAR:RHSA base: 0x000000fbffe000 proximity domain: 0x3
DMAR:RHSA base: 0x000000e7ffe000 proximity domain: 0x2
DMAR:RHSA base: 0x000000d3ffe000 proximity domain: 0x1
DMAR:RHSA base: 0x000000bfffc000 proximity domain: 0x0
DMAR:Unsupported device scope
DMAR:Unsupported device scope
DMAR:Unsupported device scope
PCI-GART: No AMD northbridge found.
pnp: 00:01: iomem range 0xfc000000-0xfcffffff has been reserved
pnp: 00:01: iomem range 0xfd000000-0xfdffffff has been reserved
pnp: 00:01: iomem range 0xfe000000-0xfeafffff has been reserved
pnp: 00:01: iomem range 0xfeb00000-0xfebfffff has been reserved
pnp: 00:02: iomem range 0xbfffc000-0xbfffdfff has been reserved
pnp: 00:0b: ioport range 0x400-0x453 could not be reserved
pnp: 00:0b: ioport range 0x458-0x47f has been reserved
pnp: 00:0b: ioport range 0x1180-0x119f has been reserved
pnp: 00:0b: ioport range 0x500-0x57f has been reserved
pnp: 00:0b: iomem range 0xfed1c000-0xfed1ffff could not be reserved
pnp: 00:0b: iomem range 0xfec00000-0xfecfffff has been reserved
pnp: 00:0b: iomem range 0xfed08000-0xfed08fff has been reserved
pnp: 00:0b: iomem range 0xff000000-0xffffffff could not be reserved
pnp: 00:0c: ioport range 0x454-0x457 has been reserved
pnp: 00:11: iomem range 0xd3ffe000-0xd3ffffff has been reserved
pnp: 00:15: iomem range 0xe7ffe000-0xe7ffffff has been reserved
pnp: 00:19: iomem range 0xfbffe000-0xfbffffff has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 4000-4fff
MEM window: bf900000-bf9fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:02.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:11.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.7
IO window: disabled.
MEM window: be000000-bf8fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 26 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 32 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:02.0 to 64
GSI 18 sharing vector 0xB9 and IRQ 18
ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 16 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:11.0 to 64
GSI 19 sharing vector 0xC1 and IRQ 19
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1c.0 to 64
GSI 20 sharing vector 0xC9 and IRQ 20
ACPI: PCI Interrupt 0000:00:1c.7[D] -> GSI 19 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1c.7 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Bridge: 0000:40:02.0
IO window: disabled.
MEM window: d3d00000-d3efffff
PREFETCH window 0x00000000d3400000-0x00000000d3bfffff
PCI: Bridge: 0000:40:03.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:40:03.1
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:40:03.2
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:40:03.3
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
GSI 21 sharing vector 0xD1 and IRQ 21
ACPI: PCI Interrupt 0000:40:02.0[A] -> GSI 56 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:40:02.0 to 64
GSI 22 sharing vector 0xD9 and IRQ 22
ACPI: PCI Interrupt 0000:40:03.0[A] -> GSI 64 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:40:03.0 to 64
ACPI: PCI Interrupt 0000:40:03.1[A] -> GSI 64 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:40:03.1 to 64
ACPI: PCI Interrupt 0000:40:03.2[A] -> GSI 64 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:40:03.2 to 64
ACPI: PCI Interrupt 0000:40:03.3[A] -> GSI 64 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:40:03.3 to 64
PCI: Bridge: 0000:c0:02.0
IO window: disabled.
MEM window: fbd00000-fbefffff
PREFETCH window: disabled.
GSI 23 sharing vector 0xE1 and IRQ 23
ACPI: PCI Interrupt 0000:c0:02.0[A] -> GSI 104 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:c0:02.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 524288 (order: 10, 4194304 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
type=2000 audit(1375588366.793:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
alg: No test for crc32c (crc32c-generic)
ksign: Installing public key data
Loading keyring
- Added public key F43E909AB54B946C
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:05:00.0
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: Setting latency timer of device 0000:00:11.0 to 64
PCI: Setting latency timer of device 0000:00:1c.0 to 64
PCI: Setting latency timer of device 0000:00:1c.7 to 64
PCI: Setting latency timer of device 0000:40:02.0 to 64
PCI: Setting latency timer of device 0000:40:03.0 to 64
PCI: Setting latency timer of device 0000:40:03.1 to 64
PCI: Setting latency timer of device 0000:40:03.2 to 64
PCI: Setting latency timer of device 0000:40:03.3 to 64
PCI: Setting latency timer of device 0000:c0:02.0 to 64
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Monitor-Mwait will be used to enter C-1 state
ACPI: Processor [CPU0] (supports 1 throttling states)
ACPI: Processor [CPU20] (supports 1 throttling states)
ACPI: Processor [CPU1] (supports 1 throttling states)
ACPI: Processor [CPU21] (supports 1 throttling states)
ACPI: Processor [CPU2] (supports 1 throttling states)
ACPI: Processor [CPU22] (supports 1 throttling states)
ACPI: Processor [CPU3] (supports 1 throttling states)
ACPI: Processor [CPU23] (supports 1 throttling states)
ACPI: Processor [CPU4] (supports 1 throttling states)
ACPI: Processor [CPU24] (supports 1 throttling states)
ACPI: Processor [CPU5] (supports 1 throttling states)
ACPI: Processor [CPU25] (supports 1 throttling states)
ACPI: Processor [CPU6] (supports 1 throttling states)
ACPI: Processor [CPU26] (supports 1 throttling states)
ACPI: Processor [CPU7] (supports 1 throttling states)
ACPI: Processor [CPU27] (supports 1 throttling states)
ACPI: Processor [CPU8] (supports 1 throttling states)
ACPI: Processor [CPU28] (supports 1 throttling states)
ACPI: Processor [CPU9] (supports 1 throttling states)
ACPI: Processor [CPU29] (supports 1 throttling states)
ACPI: Processor [CPUA] (supports 1 throttling states)
ACPI: Processor [CPU2A] (supports 1 throttling states)
ACPI: Processor [CPUB] (supports 1 throttling states)
ACPI: Processor [CPU2B] (supports 1 throttling states)
ACPI: Processor [CPUC] (supports 1 throttling states)
ACPI: Processor [CPU2C] (supports 1 throttling states)
ACPI: Processor [CPUD] (supports 1 throttling states)
ACPI: Processor [CPU2D] (supports 1 throttling states)
ACPI: Processor [CPUE] (supports 1 throttling states)
ACPI: Processor [CPU2E] (supports 1 throttling states)
ACPI: Processor [CPUF] (supports 1 throttling states)
ACPI: Processor [CPU2F] (supports 1 throttling states)
ACPI: Processor [CPU10] (supports 1 throttling states)
ACPI: Processor [CPU30] (supports 1 throttling states)
ACPI: Processor [CPU11] (supports 1 throttling states)
ACPI: Processor [CPU31] (supports 1 throttling states)
ACPI: Processor [CPU12] (supports 1 throttling states)
ACPI: Processor [CPU32] (supports 1 throttling states)
ACPI: Processor [CPU13] (supports 1 throttling states)
ACPI: Processor [CPU33] (supports 1 throttling states)
ACPI: Processor [CPU14] (supports 1 throttling states)
ACPI: Processor [CPU34] (supports 1 throttling states)
ACPI: Processor [CPU15] (supports 1 throttling states)
ACPI: Processor [CPU35] (supports 1 throttling states)
ACPI: Processor [CPU16] (supports 1 throttling states)
ACPI: Processor [CPU36] (supports 1 throttling states)
ACPI: Processor [CPU17] (supports 1 throttling states)
ACPI: Processor [CPU37] (supports 1 throttling states)
ACPI: Processor [CPU18] (supports 1 throttling states)
ACPI: Processor [CPU38] (supports 1 throttling states)
ACPI: Processor [CPU19] (supports 1 throttling states)
ACPI: Processor [CPU39] (supports 1 throttling states)
ACPI: Processor [CPU1A] (supports 1 throttling states)
ACPI: Processor [CPU3A] (supports 1 throttling states)
ACPI: Processor [CPU1B] (supports 1 throttling states)
ACPI: Processor [CPU3B] (supports 1 throttling states)
ACPI: Processor [CPU1C] (supports 1 throttling states)
ACPI: Processor [CPU3C] (supports 1 throttling states)
ACPI: Processor [CPU1D] (supports 1 throttling states)
ACPI: Processor [CPU3D] (supports 1 throttling states)
ACPI: Processor [CPU1E] (supports 1 throttling states)
ACPI: Processor [CPU3E] (supports 1 throttling states)
ACPI: Processor [CPU1F] (supports 1 throttling states)
ACPI: Processor [CPU3F] (supports 1 throttling states)
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:03: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:04: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
brd: module loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
i8042.c: No controller found.
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S5)
Initalizing network drop monitor service
Freeing unused kernel memory: 224k freed
Write protecting the kernel read-only data: 519k
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1a.0 to 64
ehci_hcd 0000:00:1a.0: EHCI Host Controller
ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.0: debug port 2
PCI: cache line size of 32 is not supported by device 0000:00:1a.0
ehci_hcd 0000:00:1a.0: irq 185, io mem 0xbfa02000
ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
GSI 24 sharing vector 0x8A and IRQ 24
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 138
PCI: Setting latency timer of device 0000:00:1d.0 to 64
ehci_hcd 0000:00:1d.0: EHCI Host Controller
ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.0: debug port 2
PCI: cache line size of 32 is not supported by device 0000:00:1d.0
ehci_hcd 0000:00:1d.0: irq 138, io mem 0xbfa01000
ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v3.0
SCSI subsystem initialized
megasas: 06.505.02.00 Wed. Nov. 14 17:00:00 PDT 2012
megasas: 0x1000:0x005b:0x1137:0x008d: bus 1:slot 0:func 0
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 26 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:01:00.0 to 64
gen2: instance->base_addr = bf960000<6>megasas: FW now in Ready state
megasas:IOC Init cmd success
megasas: INIT adapter done
megasas: max_sectors : 0x230, cmd_per_lun : 0x100
scsi0 : LSI SAS based MegaRAID driver
Vendor: LSI Model: MR9265-8i Rev: 3.15
Type: Direct-Access ANSI SCSI revision: 05
Vendor: LSI Model: MR9265-8i Rev: 3.15
Type: Direct-Access ANSI SCSI revision: 05
Vendor: LSI Model: MR9265-8i Rev: 3.15
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 285155328 512-byte hdwr sectors (146000 MB)
sda: Write Protect is off
sda: Mode Sense: 1f 00 00 08
SCSI device sda: drive cache: write back
SCSI device sda: 285155328 512-byte hdwr sectors (146000 MB)
sda: Write Protect is off
sda: Mode Sense: 1f 00 00 08
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
usb 1-1: new high speed USB device using ehci_hcd and address 2
sd 0:2:0:0: Attached scsi disk sda
Vendor: LSI Model: MR9265-8i Rev: 3.15
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 1751949312 512-byte hdwr sectors (896998 MB)
sdb: Write Protect is off
sdb: Mode Sense: 1f 00 00 08
SCSI device sdb: drive cache: write back
SCSI device sdb: 1751949312 512-byte hdwr sectors (896998 MB)
sdb: Write Protect is off
sdb: Mode Sense: 1f 00 00 08
SCSI device sdb: drive cache: write back
sdb: sdb1
sd 0:2:1:0: Attached scsi disk sdb
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Emulex LightPulse Fibre Channel SCSI driver 8.2.0.87.1p
Copyright(c) 2004-2009 Emulex. All rights reserved.
Initializing USB Mass Storage driver...
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 6 ports detected
usb 2-1: new high speed USB device using ehci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 8 ports detected
usb 2-1.3: new high speed USB device using ehci_hcd and address 3
usb 2-1.3: configuration #1 chosen from 1 choice
usb 2-1.4: new full speed USB device using ehci_hcd and address 4
usb 2-1.4: configuration #1 chosen from 1 choice
input: Avocent Cisco USB Composite Device-0 as /class/input/input0
input: USB HID v1.00 Keyboard [Avocent Cisco USB Composite Device-0] on usb-0000:00:1d.0-1.4
input: Avocent Cisco USB Composite Device-0 as /class/input/input1
input: USB HID v1.00 Mouse [Avocent Cisco USB Composite Device-0] on usb-0000:00:1d.0-1.4
input: Avocent Cisco USB Composite Device-0 as /class/input/input2
input: USB HID v1.00 Mouse [Avocent Cisco USB Composite Device-0] on usb-0000:00:1d.0-1.4
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Vendor: UNIGEN Model: PSE4000S3 Rev: PMAP
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdc: 7831552 512-byte hdwr sectors (4010 MB)
sdc: Write Protect is off
sdc: Mode Sense: 23 00 00 00
sdc: assuming drive cache: write through
SCSI device sdc: 7831552 512-byte hdwr sectors (4010 MB)
sdc: Write Protect is off
sdc: Mode Sense: 23 00 00 00
sdc: assuming drive cache: write through
sdc: sdc1
sd 1:0:0:0: Attached scsi removable disk sdc
usb-storage: device scan complete
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.11.5-ioctl (2007-12-12) initialised: dm-devel@redhat.com
device-mapper: dm-raid45: initialized v0.2594l
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
type=1404 audit(1375588399.112:2): selinux=0 auid=4294967295 ses=4294967295
sd 0:2:0:0: Attached scsi generic sg0 type 0
sd 0:2:1:0: Attached scsi generic sg1 type 0
sd 1:0:0:0: Attached scsi generic sg2 type 0
input: PC Speaker as /class/input/input3
iomemory_vsl: module license 'Proprietary' taints kernel.
fioinf VSL configuration hash: d15bf7c78eaf00bf62421df68a96065f0a01516f
fioinf
fioinf Copyright (c) 2006-2013 Fusion-io, Inc. All rights reserved.
fioinf For Terms and Conditions see the License file included
fioinf with this driver package.
fioinf
fioinf ioDrive driver 3.2.3.950 pinnacles@02042bfa64d7 loading...
ACPI: PCI Interrupt 0000:c1:00.0[A] -> GSI 104 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:c1:00.0 to 64
fioinf ioDrive 0000:c1:00.0: mapping controller on BAR 5
fioinf ioDrive 0000:c1:00.0: MSI enabled
fioinf ioDrive 0000:c1:00.0: using MSI interrupts
QLogic 1/10 GbE Converged/Intelligent Ethernet Driver v5.0.7
ACPI: PCI Interrupt 0000:41:00.0[A] -> GSI 56 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:41:00.0 to 64
qlcnic 0000:41:00.0: 2MB memory map
fioinf ioDrive 0000:c1:00.0.0: Starting master controller
QLogic Fibre Channel HBA Driver
GSI 25 sharing vector 0x5B and IRQ 25
ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 91
fioinf ioDrive 0000:c1:00.0.0: SMP Controller Firmware APP version 1.0.8 0
fioinf ioDrive 0000:c1:00.0.0: SMP Controller Firmware BOOT version 1.0.4 1
qlcnic 0000:41:00.0: phy port: 0 switch_mode: 0,
max_tx_q: 1 max_rx_q: 8 min_tx_bw: 0x0,
max_tx_bw: 0x64 max_mtu:0x2580, capabilities: 0xdeeaffae
qlcnic: 00:0e:1e:0b:18:c0 Gigabit Ethernet Board Chip rev 0x58
qlcnic 0000:41:00.0: firmware v4.9.73
qlcnic 0000:41:00.0: phy port: 0 switch_mode: 0,
max_tx_q: 1 max_rx_q: 8 min_tx_bw: 0x0,
max_tx_bw: 0x64 max_mtu:0x2580, capabilities: 0xdeeaffae
qlcnic 0000:41:00.0: using msi-x interrupts
qlcnic 0000:41:00.0: eth0: XGbE port initialized
ACPI: PCI Interrupt 0000:41:00.1[A] -> GSI 56 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:41:00.1 to 64
qlcnic 0000:41:00.1: 2MB memory map
qlcnic 0000:41:00.1: phy port: 1 switch_mode: 0,
max_tx_q: 1 max_rx_q: 8 min_tx_bw: 0x0,
max_tx_bw: 0x64 max_mtu:0x2580, capabilities: 0xdeeaffae
qlcnic 0000:41:00.1: firmware v4.9.73
qlcnic 0000:41:00.1: phy port: 1 switch_mode: 0,
max_tx_q: 1 max_rx_q: 8 min_tx_bw: 0x0,
max_tx_bw: 0x64 max_mtu:0x2580, capabilities: 0xdeeaffae
qlcnic 0000:41:00.1: using msi-x interrupts
qlcnic 0000:41:00.1: eth1: XGbE port initialized
ACPI: PCI Interrupt 0000:41:00.6[A] -> GSI 56 (level, low) -> IRQ 209
qla2xxx 0000:41:00.6: Found an ISP8021, irq 209, iobase 0xffffc200109bf000
qla2xxx 0000:41:00.6: Configuring PCI space...
PCI: Setting latency timer of device 0000:41:00.6 to 64
fioinf ioDrive 0000:c1:00.0.0: Required PCIE bandwidth 2.000 GBytes per sec
fioinf ioDrive 0000:c1:00.0.0: Board serial number is 1244D13EB
fioinf ioDrive 0000:c1:00.0.0: Default capacity 365.000 GBytes
fioinf ioDrive 0000:c1:00.0.0: Default sector size 512 bytes
fioinf ioDrive 0000:c1:00.0.0: Rated endurance 4.00 PBytes
fioinf ioDrive 0000:c1:00.0.0: 100C temp range hardware found
fioinf ioDrive 0000:c1:00.0.0: Maximum capacity 395.000 GBytes
fioinf ioDrive 0000:c1:00.0.0: Firmware version 7.1.13 109322 (0x70040d 0x1ab0a)
fioinf ioDrive 0000:c1:00.0.0: Firmware VCS version 109322 [0x1ab0a]
fioinf ioDrive 0000:c1:00.0.0: Firmware VCS uid 0x02a0b00fd435f92c3cebbf431f69bd563a77cfe3
fioinf ioDrive 0000:c1:00.0.0: Powercut flush: Enabled
fioinf ioDrive 0000:c1:00.0.0: Thermal monitoring: Enabled
fioinf ioDrive 0000:c1:00.0.0: Hardware temperature alarm set for 100C.
fioinf ioDrive 0000:c1:00.0: Found device fct0 (Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0) on pipeline 0
qla2xxx 0000:41:00.6: Configure NVRAM parameters...
qla2xxx 0000:41:00.6: Verifying loaded RISC code...
qla2xxx 0000:41:00.6: qla82xx_set_drv_active(2): drv_active = 0x11
qla2xxx 0000:41:00.6: 1:Device state is 0x3 = Ready
qla2xxx 0000:41:00.6: 2:Device state is 0x3 = Ready
scsi2 : qla2xxx
qla2xxx 0000:41:00.6:
QLogic Fibre Channel HBA Driver: 8.03.01.05.05.06-k
QLogic QMC8242 - Cisco UCS CNA M73KR-QLogic
ISP8021: PCIe (2.5Gb/s x8) @ 0000:41:00.6 hdma+, host#=2, fw=4.09.73 (804)
ACPI: PCI Interrupt 0000:41:00.7[A] -> GSI 56 (level, low) -> IRQ 209
qla2xxx 0000:41:00.7: Found an ISP8021, irq 209, iobase 0xffffc200118bf800
qla2xxx 0000:41:00.7: Configuring PCI space...
PCI: Setting latency timer of device 0000:41:00.7 to 64
fioinf Waiting for /dev/fct0 to be created
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: probed fct0
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: sector_size=512
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: setting channel range data to [2 .. 2047]
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: ***************************************************
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: *** unclean shutdown detected, re-scanning log. ***
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: *** this may take several minutes. ***
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: ***************************************************
qla2xxx 0000:41:00.7: Configure NVRAM parameters...
qla2xxx 0000:41:00.7: Verifying loaded RISC code...
qla2xxx 0000:41:00.7: qla82xx_set_drv_active(3): drv_active = 0x1000011
qla2xxx 0000:41:00.7: 1:Device state is 0x3 = Ready
qla2xxx 0000:41:00.7: 2:Device state is 0x3 = Ready
scsi3 : qla2xxx
qla2xxx 0000:41:00.7:
QLogic Fibre Channel HBA Driver: 8.03.01.05.05.06-k
QLogic QMC8242 - Cisco UCS CNA M73KR-QLogic
ISP8021: PCIe (2.5Gb/s x8) @ 0000:41:00.7 hdma+, host#=3, fw=4.09.73 (804)
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: Successfully reattached after unclean shutdown. (AP: 339+228114432)
fioinf enable_discard set but discard not supported on this linux version
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: Creating block device fioa: major: 252 minor: 0 sector size: 512...
fioa: fioa1
fioinf Waiting for /dev/fioa to be created
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: Attach succeeded.
floppy0: no floppy controllers found
work still pending
lp: driver loaded but no devices found
mtrr: type mismatch for be000000,400000 old: write-back new: write-combining
mtrr: type mismatch for be000000,1000000 old: write-back new: write-combining
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Mapper loaded
dell-wmi: No known WMI GUID found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on sda2, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
EXT4-fs (sdb1): mounted filesystem with ordered data mode
EXT4-fs (fioa1): mounted filesystem with ordered data mode
Adding 104412k swap on /dev/sda3. Priority:-1 extents:1 across:104412k
Loading iSCSI transport class v2.0-871.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
cxgb3i: tag itt 0x1fff, 13 bits, age 0xf, 4 bits.
iscsi: registered transport (cxgb3i)
IPv6: Loaded, but administratively disabled, reboot required to enable
Broadcom NetXtreme II CNIC Driver cnic v2.1.2 (May 26, 2010)
Broadcom NetXtreme II iSCSI Driver bnx2i v2.1.3 (Aug 10, 2010)
iscsi: registered transport (bnx2i)
iscsi: registered transport (tcp)
iscsi: registered transport (iser)
iscsi: registered transport (be2iscsi)
qlcnic 0000:41:00.0: NIC Link is up
qlcnic 0000:41:00.0: NIC Link is down
qlcnic 0000:41:00.1: NIC Link is up
qlcnic 0000:41:00.1: NIC Link is down
qlcnic 0000:41:00.0: NIC Link is up
qlcnic 0000:41:00.1: NIC Link is up
mtrr: type mismatch for be000000,400000 old: write-back new: write-combining
mtrr: type mismatch for be000000,1000000 old: write-back new: write-combining
FS-Cache: Loaded
qlcnic 0000:41:00.0: NIC Link is up
qlcnic 0000:41:00.1: NIC Link is up
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
mtrr: type mismatch for be000000,400000 old: write-back new: write-combining
mtrr: type mismatch for be000000,1000000 old: write-back new: write-combining
loop: loaded (max 8 devices)
Command line: ro root=LABEL=/ rhgb quiet
BIOS-provided physical RAM map:
BIOS-e820: 0000000000010000 - 000000000009ec00 (usable)
BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007e59b000 (usable)
BIOS-e820: 000000007e59b000 - 000000007e617000 (ACPI data)
BIOS-e820: 000000007e617000 - 000000007f469000 (reserved)
BIOS-e820: 000000007f469000 - 000000007f471000 (ACPI NVS)
BIOS-e820: 000000007f471000 - 000000007f499000 (reserved)
BIOS-e820: 000000007f499000 - 000000007f800000 (ACPI NVS)
BIOS-e820: 0000000080000000 - 0000000090000000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed40000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000006880000000 (usable)
DMI 2.7 present.
ACPI: RSDP (v002 Cisco ) @ 0x00000000000f0490
ACPI: XSDT (v001 Cisco CiscoUCS 0x00000000 AMI 0x00010013) @ 0x000000007e59b090
ACPI: FADT (v004 Cisco CiscoUCS 0x00000000 AMI 0x00010013) @ 0x000000007e5a4ee0
ACPI: MADT (v003 Cisco CiscoUCS 0x00000000 AMI 0x00010013) @ 0x000000007e5a4fd8
ACPI: MCFG (v001 Cisco CiscoUCS 0x00000000 MSFT 0x00000097) @ 0x000000007e5a5260
ACPI: PRAD (v002 Cisco CiscoUCS 0x00000001 MSFT 0x03000001) @ 0x000000007e5a52a0
ACPI: SLIC (v001 Cisco CiscoUCS 0x00000000 AMI 0x00010013) @ 0x000000007e5a5360
ACPI: SRAT (v003 Cisco CiscoUCS 0x00000001 AMI. 0x00000000) @ 0x000000007e5a54d8
ACPI: SLIT (v001 Cisco CiscoUCS 0x00000000 AMI. 0x00000000) @ 0x000000007e5a5e08
ACPI: HPET (v001 Cisco CiscoUCS 0x00000000 AMI. 0x00000004) @ 0x000000007e5a5e48
ACPI: SPMI (v005 Cisco CiscoUCS 0x00000000 AMI. 0x00000000) @ 0x000000007e5a5e80
ACPI: SSDT (v002 Cisco CiscoUCS 0x00004000 INTL 0x20051117) @ 0x000000007e5a5ec0
ACPI: SPCR (v001 Cisco CiscoUCS 0x00000000 AMI. 0x00000004) @ 0x000000007e615fc8
ACPI: DMAR (v001 Cisco CiscoUCS 0x00000001 INTL 0x00000001) @ 0x000000007e616018
ACPI: EINJ (v001 Cisco CiscoUCS 0x00000000 0x00000000) @ 0x000000007e6161a8
ACPI: ERST (v001 Cisco CiscoUCS 0x00000000 0x00000000) @ 0x000000007e6162d8
ACPI: HEST (v001 Cisco CiscoUCS 0x00000000 0x00000000) @ 0x000000007e6164e8
ACPI: BERT (v001 Cisco CiscoUCS 0x00000000 0x00000000) @ 0x000000007e616590
ACPI: DSDT (v002 Cisco CiscoUCS 0x00000000 INTL 0x20091112) @ 0x0000000000000000
SRAT: PXM 0 -> APIC 0 -> Node 0
SRAT: PXM 0 -> APIC 1 -> Node 0
SRAT: PXM 0 -> APIC 2 -> Node 0
SRAT: PXM 0 -> APIC 3 -> Node 0
SRAT: PXM 0 -> APIC 4 -> Node 0
SRAT: PXM 0 -> APIC 5 -> Node 0
SRAT: PXM 0 -> APIC 6 -> Node 0
SRAT: PXM 0 -> APIC 7 -> Node 0
SRAT: PXM 0 -> APIC 8 -> Node 0
SRAT: PXM 0 -> APIC 9 -> Node 0
SRAT: PXM 0 -> APIC 10 -> Node 0
SRAT: PXM 0 -> APIC 11 -> Node 0
SRAT: PXM 0 -> APIC 12 -> Node 0
SRAT: PXM 0 -> APIC 13 -> Node 0
SRAT: PXM 0 -> APIC 14 -> Node 0
SRAT: PXM 0 -> APIC 15 -> Node 0
SRAT: PXM 1 -> APIC 32 -> Node 1
SRAT: PXM 1 -> APIC 33 -> Node 1
SRAT: PXM 1 -> APIC 34 -> Node 1
SRAT: PXM 1 -> APIC 35 -> Node 1
SRAT: PXM 1 -> APIC 36 -> Node 1
SRAT: PXM 1 -> APIC 37 -> Node 1
SRAT: PXM 1 -> APIC 38 -> Node 1
SRAT: PXM 1 -> APIC 39 -> Node 1
SRAT: PXM 1 -> APIC 40 -> Node 1
SRAT: PXM 1 -> APIC 41 -> Node 1
SRAT: PXM 1 -> APIC 42 -> Node 1
SRAT: PXM 1 -> APIC 43 -> Node 1
SRAT: PXM 1 -> APIC 44 -> Node 1
SRAT: PXM 1 -> APIC 45 -> Node 1
SRAT: PXM 1 -> APIC 46 -> Node 1
SRAT: PXM 1 -> APIC 47 -> Node 1
SRAT: PXM 2 -> APIC 64 -> Node 2
SRAT: PXM 2 -> APIC 65 -> Node 2
SRAT: PXM 2 -> APIC 66 -> Node 2
SRAT: PXM 2 -> APIC 67 -> Node 2
SRAT: PXM 2 -> APIC 68 -> Node 2
SRAT: PXM 2 -> APIC 69 -> Node 2
SRAT: PXM 2 -> APIC 70 -> Node 2
SRAT: PXM 2 -> APIC 71 -> Node 2
SRAT: PXM 2 -> APIC 72 -> Node 2
SRAT: PXM 2 -> APIC 73 -> Node 2
SRAT: PXM 2 -> APIC 74 -> Node 2
SRAT: PXM 2 -> APIC 75 -> Node 2
SRAT: PXM 2 -> APIC 76 -> Node 2
SRAT: PXM 2 -> APIC 77 -> Node 2
SRAT: PXM 2 -> APIC 78 -> Node 2
SRAT: PXM 2 -> APIC 79 -> Node 2
SRAT: PXM 3 -> APIC 96 -> Node 3
SRAT: PXM 3 -> APIC 97 -> Node 3
SRAT: PXM 3 -> APIC 98 -> Node 3
SRAT: PXM 3 -> APIC 99 -> Node 3
SRAT: PXM 3 -> APIC 100 -> Node 3
SRAT: PXM 3 -> APIC 101 -> Node 3
SRAT: PXM 3 -> APIC 102 -> Node 3
SRAT: PXM 3 -> APIC 103 -> Node 3
SRAT: PXM 3 -> APIC 104 -> Node 3
SRAT: PXM 3 -> APIC 105 -> Node 3
SRAT: PXM 3 -> APIC 106 -> Node 3
SRAT: PXM 3 -> APIC 107 -> Node 3
SRAT: PXM 3 -> APIC 108 -> Node 3
SRAT: PXM 3 -> APIC 109 -> Node 3
SRAT: PXM 3 -> APIC 110 -> Node 3
SRAT: PXM 3 -> APIC 111 -> Node 3
SRAT: Node 0 PXM 0 0-80000000
SRAT: Node 0 PXM 0 0-2080000000
SRAT: Node 1 PXM 1 2080000000-3880000000
SRAT: Node 2 PXM 2 3880000000-5080000000
SRAT: Node 3 PXM 3 5080000000-6880000000
NUMA: Using 31 for the hash shift.
Bootmem setup node 0 0000000000000000-0000002080000000
Bootmem setup node 1 0000002080000000-0000003880000000
Bootmem setup node 2 0000003880000000-0000005080000000
Bootmem setup node 3 0000005080000000-0000006880000000
Memory for crash kernel (0x0 to 0x0) notwithin permissible range
disabling kdump
On node 0 totalpages: 33079737
DMA zone: 2022 pages, LIFO batch:0
DMA32 zone: 499155 pages, LIFO batch:31
Normal zone: 32578560 pages, LIFO batch:31
On node 1 totalpages: 24821760
Normal zone: 24821760 pages, LIFO batch:31
On node 2 totalpages: 24821760
Normal zone: 24821760 pages, LIFO batch:31
On node 3 totalpages: 24821760
Normal zone: 24821760 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
Processor #2 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] enabled)
Processor #4 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] enabled)
Processor #6 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x08] enabled)
Processor #8 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x0a] enabled)
Processor #10 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x0c] enabled)
Processor #12 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x0e] enabled)
Processor #14 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x10] lapic_id[0x20] enabled)
Processor #32 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x12] lapic_id[0x22] enabled)
Processor #34 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x14] lapic_id[0x24] enabled)
Processor #36 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x16] lapic_id[0x26] enabled)
Processor #38 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x18] lapic_id[0x28] enabled)
Processor #40 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x1a] lapic_id[0x2a] enabled)
Processor #42 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x1c] lapic_id[0x2c] enabled)
Processor #44 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x1e] lapic_id[0x2e] enabled)
Processor #46 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x20] lapic_id[0x40] enabled)
Processor #64 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x22] lapic_id[0x42] enabled)
Processor #66 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x24] lapic_id[0x44] enabled)
Processor #68 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x26] lapic_id[0x46] enabled)
Processor #70 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x28] lapic_id[0x48] enabled)
Processor #72 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x2a] lapic_id[0x4a] enabled)
Processor #74 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x2c] lapic_id[0x4c] enabled)
Processor #76 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x2e] lapic_id[0x4e] enabled)
Processor #78 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x30] lapic_id[0x60] enabled)
Processor #96 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x32] lapic_id[0x62] enabled)
Processor #98 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x34] lapic_id[0x64] enabled)
Processor #100 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x36] lapic_id[0x66] enabled)
Processor #102 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x38] lapic_id[0x68] enabled)
Processor #104 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x3a] lapic_id[0x6a] enabled)
Processor #106 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x3c] lapic_id[0x6c] enabled)
Processor #108 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x3e] lapic_id[0x6e] enabled)
Processor #110 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
Processor #3 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x05] enabled)
Processor #5 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled)
Processor #7 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x09] lapic_id[0x09] enabled)
Processor #9 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x0b] enabled)
Processor #11 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x0d] enabled)
Processor #13 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x0f] enabled)
Processor #15 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x11] lapic_id[0x21] enabled)
Processor #33 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x13] lapic_id[0x23] enabled)
Processor #35 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x15] lapic_id[0x25] enabled)
Processor #37 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x17] lapic_id[0x27] enabled)
Processor #39 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x19] lapic_id[0x29] enabled)
Processor #41 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x1b] lapic_id[0x2b] enabled)
Processor #43 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x1d] lapic_id[0x2d] enabled)
Processor #45 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x1f] lapic_id[0x2f] enabled)
Processor #47 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x21] lapic_id[0x41] enabled)
Processor #65 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x23] lapic_id[0x43] enabled)
Processor #67 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x25] lapic_id[0x45] enabled)
Processor #69 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x27] lapic_id[0x47] enabled)
Processor #71 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x29] lapic_id[0x49] enabled)
Processor #73 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x2b] lapic_id[0x4b] enabled)
Processor #75 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x2d] lapic_id[0x4d] enabled)
Processor #77 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x2f] lapic_id[0x4f] enabled)
Processor #79 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x31] lapic_id[0x61] enabled)
Processor #97 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x33] lapic_id[0x63] enabled)
Processor #99 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x35] lapic_id[0x65] enabled)
Processor #101 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x37] lapic_id[0x67] enabled)
Processor #103 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x39] lapic_id[0x69] enabled)
Processor #105 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x3b] lapic_id[0x6b] enabled)
Processor #107 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x3d] lapic_id[0x6d] enabled)
Processor #109 6:13 APIC version 21
ACPI: LAPIC (acpi_id[0x3f] lapic_id[0x6f] enabled)
Processor #111 6:13 APIC version 21
ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x02] address[0xfec01000] gsi_base[24])
IOAPIC[1]: apic_id 2, version 32, address 0xfec01000, GSI 24-47
ACPI: IOAPIC (id[0x03] address[0xfec40000] gsi_base[48])
IOAPIC[2]: apic_id 3, version 32, address 0xfec40000, GSI 48-71
ACPI: IOAPIC (id[0x04] address[0xfec80000] gsi_base[72])
IOAPIC[3]: apic_id 4, version 32, address 0xfec80000, GSI 72-95
ACPI: IOAPIC (id[0x05] address[0xfecc0000] gsi_base[96])
IOAPIC[4]: apic_id 5, version 32, address 0xfecc0000, GSI 96-119
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to physical flat
ACPI: HPET id: 0x8086a701 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000009e000 - 000000000009f000
Nosave address range: 000000000009f000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 00000000000e0000
Nosave address range: 00000000000e0000 - 0000000000100000
Nosave address range: 000000007e59b000 - 000000007e617000
Nosave address range: 000000007e617000 - 000000007f469000
Nosave address range: 000000007f469000 - 000000007f471000
Nosave address range: 000000007f471000 - 000000007f499000
Nosave address range: 000000007f499000 - 000000007f800000
Nosave address range: 000000007f800000 - 0000000080000000
Nosave address range: 0000000080000000 - 0000000090000000
Nosave address range: 0000000090000000 - 00000000fed1c000
Nosave address range: 00000000fed1c000 - 00000000fed40000
Nosave address range: 00000000fed40000 - 00000000ff000000
Nosave address range: 00000000ff000000 - 0000000100000000
Allocating PCI resources starting at 98000000 (gap: 90000000:6ed1c000)
SMP: Allowing 64 CPUs, 0 hotplug CPUs
Built 4 zonelists. Total pages: 107545017
Kernel command line: ro root=LABEL=/ rhgb quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 67108864 (order: 17, 536870912 bytes)
Inode-cache hash table entries: 33554432 (order: 16, 268435456 bytes)
Checking aperture...
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing software IO TLB between 0x310a3000 - 0x350a3000
Memory: 429321636k/438304768k available (2592k kernel code, 6858496k reserved, 1649k data, 224k init)
Calibrating delay loop (skipped), value calculated using timer frequency.. 5400.22 BogoMIPS (lpj=2700112)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 0/0 -> Node 0
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM1)
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
Using local APIC timer interrupts.
Detected 6.250 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/64 APIC 0x2
Initializing CPU#1
Calibrating delay using timer specific routine.. 5399.99 BogoMIPS (lpj=2699996)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 1/2 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 2/64 APIC 0x4
Initializing CPU#2
Calibrating delay using timer specific routine.. 5399.84 BogoMIPS (lpj=2699924)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 2/4 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
CPU2: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 3/64 APIC 0x6
Initializing CPU#3
Calibrating delay using timer specific routine.. 5400.00 BogoMIPS (lpj=2700003)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 3/6 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 3
CPU3: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 4/64 APIC 0x8
Initializing CPU#4
Calibrating delay using timer specific routine.. 5399.92 BogoMIPS (lpj=2699962)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 4/8 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 4
CPU4: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 5/64 APIC 0xa
Initializing CPU#5
Calibrating delay using timer specific routine.. 5399.92 BogoMIPS (lpj=2699963)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 5/a -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 5
CPU5: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 6/64 APIC 0xc
Initializing CPU#6
Calibrating delay using timer specific routine.. 5399.92 BogoMIPS (lpj=2699963)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 6/c -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 6
CPU6: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 7/64 APIC 0xe
Initializing CPU#7
Calibrating delay using timer specific routine.. 5400.00 BogoMIPS (lpj=2700004)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 7/e -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 7
CPU7: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 8/64 APIC 0x20
Initializing CPU#8
Calibrating delay using timer specific routine.. 5400.11 BogoMIPS (lpj=2700059)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 8/20 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 0
CPU8: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 9/64 APIC 0x22
Initializing CPU#9
Calibrating delay using timer specific routine.. 5400.03 BogoMIPS (lpj=2700018)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 9/22 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 1
CPU9: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 10/64 APIC 0x24
Initializing CPU#10
Calibrating delay using timer specific routine.. 5400.11 BogoMIPS (lpj=2700056)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 10/24 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 2
CPU10: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 11/64 APIC 0x26
Initializing CPU#11
Calibrating delay using timer specific routine.. 5400.12 BogoMIPS (lpj=2700062)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 11/26 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 3
CPU11: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 12/64 APIC 0x28
Initializing CPU#12
Calibrating delay using timer specific routine.. 5400.01 BogoMIPS (lpj=2700006)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 12/28 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 4
CPU12: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 13/64 APIC 0x2a
Initializing CPU#13
Calibrating delay using timer specific routine.. 5400.16 BogoMIPS (lpj=2700081)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 13/2a -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 5
CPU13: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 14/64 APIC 0x2c
Initializing CPU#14
Calibrating delay using timer specific routine.. 5400.03 BogoMIPS (lpj=2700015)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 14/2c -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 6
CPU14: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 15/64 APIC 0x2e
Initializing CPU#15
Calibrating delay using timer specific routine.. 5400.13 BogoMIPS (lpj=2700066)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 15/2e -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 7
CPU15: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 16/64 APIC 0x40
Initializing CPU#16
Calibrating delay using timer specific routine.. 5400.05 BogoMIPS (lpj=2700025)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 16/40 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 0
CPU16: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 17/64 APIC 0x42
Initializing CPU#17
Calibrating delay using timer specific routine.. 5400.11 BogoMIPS (lpj=2700057)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 17/42 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 1
CPU17: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 18/64 APIC 0x44
Initializing CPU#18
Calibrating delay using timer specific routine.. 5400.08 BogoMIPS (lpj=2700042)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 18/44 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 2
CPU18: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 19/64 APIC 0x46
Initializing CPU#19
Calibrating delay using timer specific routine.. 5400.02 BogoMIPS (lpj=2700012)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 19/46 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 3
CPU19: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 20/64 APIC 0x48
Initializing CPU#20
Calibrating delay using timer specific routine.. 5400.10 BogoMIPS (lpj=2700051)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 20/48 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 4
CPU20: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 21/64 APIC 0x4a
Initializing CPU#21
Calibrating delay using timer specific routine.. 5400.01 BogoMIPS (lpj=2700005)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 21/4a -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 5
CPU21: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 22/64 APIC 0x4c
Initializing CPU#22
Calibrating delay using timer specific routine.. 5400.17 BogoMIPS (lpj=2700088)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 22/4c -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 6
CPU22: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 23/64 APIC 0x4e
Initializing CPU#23
Calibrating delay using timer specific routine.. 5399.94 BogoMIPS (lpj=2699970)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 23/4e -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 7
CPU23: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 24/64 APIC 0x60
Initializing CPU#24
Calibrating delay using timer specific routine.. 5400.21 BogoMIPS (lpj=2700109)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 24/60 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 0
CPU24: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 25/64 APIC 0x62
Initializing CPU#25
Calibrating delay using timer specific routine.. 5400.06 BogoMIPS (lpj=2700030)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 25/62 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 1
CPU25: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 26/64 APIC 0x64
Initializing CPU#26
Calibrating delay using timer specific routine.. 5400.14 BogoMIPS (lpj=2700070)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 26/64 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 2
CPU26: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 27/64 APIC 0x66
Initializing CPU#27
Calibrating delay using timer specific routine.. 5400.03 BogoMIPS (lpj=2700016)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 27/66 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 3
CPU27: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 28/64 APIC 0x68
Initializing CPU#28
Calibrating delay using timer specific routine.. 5400.12 BogoMIPS (lpj=2700064)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 28/68 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 4
CPU28: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 29/64 APIC 0x6a
Initializing CPU#29
Calibrating delay using timer specific routine.. 5400.05 BogoMIPS (lpj=2700026)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 29/6a -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 5
CPU29: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 30/64 APIC 0x6c
Initializing CPU#30
Calibrating delay using timer specific routine.. 5400.07 BogoMIPS (lpj=2700037)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 30/6c -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 6
CPU30: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 31/64 APIC 0x6e
Initializing CPU#31
Calibrating delay using timer specific routine.. 5400.02 BogoMIPS (lpj=2700013)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 31/6e -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 7
CPU31: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 32/64 APIC 0x1
Initializing CPU#32
Calibrating delay using timer specific routine.. 5400.05 BogoMIPS (lpj=2700027)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 32/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU32: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 33/64 APIC 0x3
Initializing CPU#33
Calibrating delay using timer specific routine.. 5400.13 BogoMIPS (lpj=2700067)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 33/3 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU33: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 34/64 APIC 0x5
Initializing CPU#34
Calibrating delay using timer specific routine.. 5400.10 BogoMIPS (lpj=2700052)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 34/5 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
CPU34: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 35/64 APIC 0x7
Initializing CPU#35
Calibrating delay using timer specific routine.. 5399.98 BogoMIPS (lpj=2699990)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 35/7 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 3
CPU35: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 36/64 APIC 0x9
Initializing CPU#36
Calibrating delay using timer specific routine.. 5400.13 BogoMIPS (lpj=2700067)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 36/9 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 4
CPU36: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 37/64 APIC 0xb
Initializing CPU#37
Calibrating delay using timer specific routine.. 5400.05 BogoMIPS (lpj=2700027)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 37/b -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 5
CPU37: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 38/64 APIC 0xd
Initializing CPU#38
Calibrating delay using timer specific routine.. 5400.13 BogoMIPS (lpj=2700069)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 38/d -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 6
CPU38: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 39/64 APIC 0xf
Initializing CPU#39
Calibrating delay using timer specific routine.. 5400.07 BogoMIPS (lpj=2700037)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 39/f -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 7
CPU39: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 40/64 APIC 0x21
Initializing CPU#40
Calibrating delay using timer specific routine.. 5400.20 BogoMIPS (lpj=2700104)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 40/21 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 0
CPU40: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 41/64 APIC 0x23
Initializing CPU#41
Calibrating delay using timer specific routine.. 5400.09 BogoMIPS (lpj=2700049)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 41/23 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 1
CPU41: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 42/64 APIC 0x25
Initializing CPU#42
Calibrating delay using timer specific routine.. 5400.07 BogoMIPS (lpj=2700037)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 42/25 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 2
CPU42: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 43/64 APIC 0x27
Initializing CPU#43
Calibrating delay using timer specific routine.. 5400.06 BogoMIPS (lpj=2700033)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 43/27 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 3
CPU43: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 44/64 APIC 0x29
Initializing CPU#44
Calibrating delay using timer specific routine.. 5400.20 BogoMIPS (lpj=2700101)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 44/29 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 4
CPU44: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 45/64 APIC 0x2b
Initializing CPU#45
Calibrating delay using timer specific routine.. 5400.15 BogoMIPS (lpj=2700075)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 45/2b -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 5
CPU45: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 46/64 APIC 0x2d
Initializing CPU#46
Calibrating delay using timer specific routine.. 5400.05 BogoMIPS (lpj=2700027)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 46/2d -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 6
CPU46: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 47/64 APIC 0x2f
Initializing CPU#47
Calibrating delay using timer specific routine.. 5400.03 BogoMIPS (lpj=2700017)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 47/2f -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 7
CPU47: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 48/64 APIC 0x41
Initializing CPU#48
Calibrating delay using timer specific routine.. 5400.00 BogoMIPS (lpj=2700000)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 48/41 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 0
CPU48: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 49/64 APIC 0x43
Initializing CPU#49
Calibrating delay using timer specific routine.. 5400.21 BogoMIPS (lpj=2700107)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 49/43 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 1
CPU49: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 50/64 APIC 0x45
Initializing CPU#50
Calibrating delay using timer specific routine.. 5400.11 BogoMIPS (lpj=2700056)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 50/45 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 2
CPU50: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 51/64 APIC 0x47
Initializing CPU#51
Calibrating delay using timer specific routine.. 5400.01 BogoMIPS (lpj=2700008)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 51/47 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 3
CPU51: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 52/64 APIC 0x49
Initializing CPU#52
Calibrating delay using timer specific routine.. 5400.02 BogoMIPS (lpj=2700010)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 52/49 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 4
CPU52: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 53/64 APIC 0x4b
Initializing CPU#53
Calibrating delay using timer specific routine.. 5400.01 BogoMIPS (lpj=2700007)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 53/4b -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 5
CPU53: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 54/64 APIC 0x4d
Initializing CPU#54
Calibrating delay using timer specific routine.. 5400.17 BogoMIPS (lpj=2700086)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 54/4d -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 6
CPU54: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 55/64 APIC 0x4f
Initializing CPU#55
Calibrating delay using timer specific routine.. 5400.09 BogoMIPS (lpj=2700049)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 55/4f -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 7
CPU55: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 56/64 APIC 0x61
Initializing CPU#56
Calibrating delay using timer specific routine.. 5400.05 BogoMIPS (lpj=2700028)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 56/61 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 0
CPU56: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 57/64 APIC 0x63
Initializing CPU#57
Calibrating delay using timer specific routine.. 5400.06 BogoMIPS (lpj=2700030)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 57/63 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 1
CPU57: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 58/64 APIC 0x65
Initializing CPU#58
Calibrating delay using timer specific routine.. 5400.06 BogoMIPS (lpj=2700031)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 58/65 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 2
CPU58: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 59/64 APIC 0x67
Initializing CPU#59
Calibrating delay using timer specific routine.. 5400.21 BogoMIPS (lpj=2700108)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 59/67 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 3
CPU59: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 60/64 APIC 0x69
Initializing CPU#60
Calibrating delay using timer specific routine.. 5400.13 BogoMIPS (lpj=2700065)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 60/69 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 4
CPU60: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 61/64 APIC 0x6b
Initializing CPU#61
Calibrating delay using timer specific routine.. 5400.25 BogoMIPS (lpj=2700126)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 61/6b -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 5
CPU61: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 62/64 APIC 0x6d
Initializing CPU#62
Calibrating delay using timer specific routine.. 5400.09 BogoMIPS (lpj=2700049)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 62/6d -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 6
CPU62: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 63/64 APIC 0x6f
Initializing CPU#63
Calibrating delay using timer specific routine.. 5400.05 BogoMIPS (lpj=2700027)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 20480K
CPU 63/6f -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 7
CPU63: Thermal monitoring enabled (TM1)
Genuine Intel(R) CPU @ 2.70GHz stepping 06
Brought up 64 CPUs
CPU#0: NMI watchdog performance counter calibration - 4606->4626
CPU#1: NMI watchdog performance counter calibration - 68->88
CPU#2: NMI watchdog performance counter calibration - 68->88
CPU#3: NMI watchdog performance counter calibration - 66->86
CPU#4: NMI watchdog performance counter calibration - 66->86
CPU#5: NMI watchdog performance counter calibration - 66->86
CPU#6: NMI watchdog performance counter calibration - 66->86
CPU#7: NMI watchdog performance counter calibration - 66->86
CPU#8: NMI watchdog performance counter calibration - 67->87
CPU#9: NMI watchdog performance counter calibration - 67->87
CPU#10: NMI watchdog performance counter calibration - 67->87
CPU#11: NMI watchdog performance counter calibration - 66->86
CPU#12: NMI watchdog performance counter calibration - 67->87
CPU#13: NMI watchdog performance counter calibration - 66->86
CPU#14: NMI watchdog performance counter calibration - 66->86
CPU#15: NMI watchdog performance counter calibration - 65->85
CPU#16: NMI watchdog performance counter calibration - 65->85
CPU#17: NMI watchdog performance counter calibration - 65->85
CPU#18: NMI watchdog performance counter calibration - 65->85
CPU#19: NMI watchdog performance counter calibration - 65->85
CPU#20: NMI watchdog performance counter calibration - 65->85
CPU#21: NMI watchdog performance counter calibration - 65->85
CPU#22: NMI watchdog performance counter calibration - 65->85
CPU#23: NMI watchdog performance counter calibration - 65->85
CPU#24: NMI watchdog performance counter calibration - 65->85
CPU#25: NMI watchdog performance counter calibration - 65->85
CPU#26: NMI watchdog performance counter calibration - 65->85
CPU#27: NMI watchdog performance counter calibration - 64->84
CPU#28: NMI watchdog performance counter calibration - 64->84
CPU#29: NMI watchdog performance counter calibration - 64->84
CPU#30: NMI watchdog performance counter calibration - 64->84
CPU#31: NMI watchdog performance counter calibration - 64->84
CPU#32: NMI watchdog performance counter calibration - 64->84
CPU#33: NMI watchdog performance counter calibration - 64->84
CPU#34: NMI watchdog performance counter calibration - 63->83
CPU#35: NMI watchdog performance counter calibration - 62->83
CPU#36: NMI watchdog performance counter calibration - 62->82
CPU#37: NMI watchdog performance counter calibration - 62->82
CPU#38: NMI watchdog performance counter calibration - 62->82
CPU#39: NMI watchdog performance counter calibration - 62->82
CPU#40: NMI watchdog performance counter calibration - 63->83
CPU#41: NMI watchdog performance counter calibration - 63->83
CPU#42: NMI watchdog performance counter calibration - 63->83
CPU#43: NMI watchdog performance counter calibration - 63->83
CPU#44: NMI watchdog performance counter calibration - 63->83
CPU#45: NMI watchdog performance counter calibration - 62->83
CPU#46: NMI watchdog performance counter calibration - 62->82
CPU#47: NMI watchdog performance counter calibration - 62->82
CPU#48: NMI watchdog performance counter calibration - 62->82
CPU#49: NMI watchdog performance counter calibration - 62->82
CPU#50: NMI watchdog performance counter calibration - 62->82
CPU#51: NMI watchdog performance counter calibration - 62->82
CPU#52: NMI watchdog performance counter calibration - 62->82
CPU#53: NMI watchdog performance counter calibration - 62->82
CPU#54: NMI watchdog performance counter calibration - 61->81
CPU#55: NMI watchdog performance counter calibration - 61->81
CPU#56: NMI watchdog performance counter calibration - 62->82
CPU#57: NMI watchdog performance counter calibration - 62->82
CPU#58: NMI watchdog performance counter calibration - 62->82
CPU#59: NMI watchdog performance counter calibration - 61->81
CPU#60: NMI watchdog performance counter calibration - 61->81
CPU#61: NMI watchdog performance counter calibration - 61->81
CPU#62: NMI watchdog performance counter calibration - 61->81
CPU#63: NMI watchdog performance counter calibration - 61->81
NMI watchdog testing PASSED.
time.c: Using 14.318180 MHz WALL HPET GTOD HPET/TSC timer.
time.c: Detected 2700.112 MHz processor.
sizeof(vma)=176 bytes
sizeof(page)=56 bytes
sizeof(inode)=560 bytes
sizeof(dentry)=216 bytes
sizeof(ext3inode)=760 bytes
sizeof(buffer_head)=96 bytes
sizeof(skbuff)=248 bytes
migration_cost=3,34,2658
checking if image is initramfs... it is
Freeing initrd memory: 3090k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at 80000000
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:1e.0
bus 0 -> pxm 0 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX7._PRT]
ACPI: PCI Root Bridge [UNC0] (0000:3f)
ACPI: PCI Root Bridge [PCI1] (0000:40)
bus 64 -> pxm 1 -> node 1
ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT]
ACPI: PCI Root Bridge [UNC1] (0000:7f)
ACPI: PCI Root Bridge [PCI2] (0000:80)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI2._PRT]
ACPI: PCI Root Bridge [UNC2] (0000:bf)
ACPI: PCI Root Bridge [PCI3] (0000:c0)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI3._PRT]
ACPI: PCI Root Bridge [UNC3] (0000:ff)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 27 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000 (virtual 0xffffffffff5fe000), IRQs 2, 8, 0, 0, 0, 0, 0, 0
hpet0: 8 64-bit timers, 14318180 Hz
DMAR:Host address width 46
DMAR:DRHD base: 0x000000fbffe000 flags: 0x0
IOMMU fbffe000: ver 1:0 cap d2078c106f0462 ecap f020fe
DMAR:DRHD base: 0x000000e7ffe000 flags: 0x0
IOMMU e7ffe000: ver 1:0 cap d2078c106f0462 ecap f020fe
DMAR:DRHD base: 0x000000d3ffe000 flags: 0x0
IOMMU d3ffe000: ver 1:0 cap d2078c106f0462 ecap f020fe
DMAR:DRHD base: 0x000000bfffc000 flags: 0x1
IOMMU bfffc000: ver 1:0 cap d2078c106f0462 ecap f020fe
DMAR:RMRR base: 0x0000007f324000 end: 0x0000007f342fff
DMAR:ATSR flags: 0x0
DMAR:RHSA base: 0x000000fbffe000 proximity domain: 0x3
DMAR:RHSA base: 0x000000e7ffe000 proximity domain: 0x2
DMAR:RHSA base: 0x000000d3ffe000 proximity domain: 0x1
DMAR:RHSA base: 0x000000bfffc000 proximity domain: 0x0
DMAR:Unsupported device scope
DMAR:Unsupported device scope
DMAR:Unsupported device scope
PCI-GART: No AMD northbridge found.
pnp: 00:01: iomem range 0xfc000000-0xfcffffff has been reserved
pnp: 00:01: iomem range 0xfd000000-0xfdffffff has been reserved
pnp: 00:01: iomem range 0xfe000000-0xfeafffff has been reserved
pnp: 00:01: iomem range 0xfeb00000-0xfebfffff has been reserved
pnp: 00:02: iomem range 0xbfffc000-0xbfffdfff has been reserved
pnp: 00:0b: ioport range 0x400-0x453 could not be reserved
pnp: 00:0b: ioport range 0x458-0x47f has been reserved
pnp: 00:0b: ioport range 0x1180-0x119f has been reserved
pnp: 00:0b: ioport range 0x500-0x57f has been reserved
pnp: 00:0b: iomem range 0xfed1c000-0xfed1ffff could not be reserved
pnp: 00:0b: iomem range 0xfec00000-0xfecfffff has been reserved
pnp: 00:0b: iomem range 0xfed08000-0xfed08fff has been reserved
pnp: 00:0b: iomem range 0xff000000-0xffffffff could not be reserved
pnp: 00:0c: ioport range 0x454-0x457 has been reserved
pnp: 00:11: iomem range 0xd3ffe000-0xd3ffffff has been reserved
pnp: 00:15: iomem range 0xe7ffe000-0xe7ffffff has been reserved
pnp: 00:19: iomem range 0xfbffe000-0xfbffffff has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 4000-4fff
MEM window: bf900000-bf9fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:02.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:11.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.7
IO window: disabled.
MEM window: be000000-bf8fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 26 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 32 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:02.0 to 64
GSI 18 sharing vector 0xB9 and IRQ 18
ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 16 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:11.0 to 64
GSI 19 sharing vector 0xC1 and IRQ 19
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1c.0 to 64
GSI 20 sharing vector 0xC9 and IRQ 20
ACPI: PCI Interrupt 0000:00:1c.7[D] -> GSI 19 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1c.7 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Bridge: 0000:40:02.0
IO window: disabled.
MEM window: d3d00000-d3efffff
PREFETCH window 0x00000000d3400000-0x00000000d3bfffff
PCI: Bridge: 0000:40:03.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:40:03.1
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:40:03.2
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:40:03.3
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
GSI 21 sharing vector 0xD1 and IRQ 21
ACPI: PCI Interrupt 0000:40:02.0[A] -> GSI 56 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:40:02.0 to 64
GSI 22 sharing vector 0xD9 and IRQ 22
ACPI: PCI Interrupt 0000:40:03.0[A] -> GSI 64 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:40:03.0 to 64
ACPI: PCI Interrupt 0000:40:03.1[A] -> GSI 64 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:40:03.1 to 64
ACPI: PCI Interrupt 0000:40:03.2[A] -> GSI 64 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:40:03.2 to 64
ACPI: PCI Interrupt 0000:40:03.3[A] -> GSI 64 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:40:03.3 to 64
PCI: Bridge: 0000:c0:02.0
IO window: disabled.
MEM window: fbd00000-fbefffff
PREFETCH window: disabled.
GSI 23 sharing vector 0xE1 and IRQ 23
ACPI: PCI Interrupt 0000:c0:02.0[A] -> GSI 104 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:c0:02.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 524288 (order: 10, 4194304 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
type=2000 audit(1375588366.793:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
alg: No test for crc32c (crc32c-generic)
ksign: Installing public key data
Loading keyring
- Added public key F43E909AB54B946C
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:05:00.0
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: Setting latency timer of device 0000:00:11.0 to 64
PCI: Setting latency timer of device 0000:00:1c.0 to 64
PCI: Setting latency timer of device 0000:00:1c.7 to 64
PCI: Setting latency timer of device 0000:40:02.0 to 64
PCI: Setting latency timer of device 0000:40:03.0 to 64
PCI: Setting latency timer of device 0000:40:03.1 to 64
PCI: Setting latency timer of device 0000:40:03.2 to 64
PCI: Setting latency timer of device 0000:40:03.3 to 64
PCI: Setting latency timer of device 0000:c0:02.0 to 64
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Monitor-Mwait will be used to enter C-1 state
ACPI: Processor [CPU0] (supports 1 throttling states)
ACPI: Processor [CPU20] (supports 1 throttling states)
ACPI: Processor [CPU1] (supports 1 throttling states)
ACPI: Processor [CPU21] (supports 1 throttling states)
ACPI: Processor [CPU2] (supports 1 throttling states)
ACPI: Processor [CPU22] (supports 1 throttling states)
ACPI: Processor [CPU3] (supports 1 throttling states)
ACPI: Processor [CPU23] (supports 1 throttling states)
ACPI: Processor [CPU4] (supports 1 throttling states)
ACPI: Processor [CPU24] (supports 1 throttling states)
ACPI: Processor [CPU5] (supports 1 throttling states)
ACPI: Processor [CPU25] (supports 1 throttling states)
ACPI: Processor [CPU6] (supports 1 throttling states)
ACPI: Processor [CPU26] (supports 1 throttling states)
ACPI: Processor [CPU7] (supports 1 throttling states)
ACPI: Processor [CPU27] (supports 1 throttling states)
ACPI: Processor [CPU8] (supports 1 throttling states)
ACPI: Processor [CPU28] (supports 1 throttling states)
ACPI: Processor [CPU9] (supports 1 throttling states)
ACPI: Processor [CPU29] (supports 1 throttling states)
ACPI: Processor [CPUA] (supports 1 throttling states)
ACPI: Processor [CPU2A] (supports 1 throttling states)
ACPI: Processor [CPUB] (supports 1 throttling states)
ACPI: Processor [CPU2B] (supports 1 throttling states)
ACPI: Processor [CPUC] (supports 1 throttling states)
ACPI: Processor [CPU2C] (supports 1 throttling states)
ACPI: Processor [CPUD] (supports 1 throttling states)
ACPI: Processor [CPU2D] (supports 1 throttling states)
ACPI: Processor [CPUE] (supports 1 throttling states)
ACPI: Processor [CPU2E] (supports 1 throttling states)
ACPI: Processor [CPUF] (supports 1 throttling states)
ACPI: Processor [CPU2F] (supports 1 throttling states)
ACPI: Processor [CPU10] (supports 1 throttling states)
ACPI: Processor [CPU30] (supports 1 throttling states)
ACPI: Processor [CPU11] (supports 1 throttling states)
ACPI: Processor [CPU31] (supports 1 throttling states)
ACPI: Processor [CPU12] (supports 1 throttling states)
ACPI: Processor [CPU32] (supports 1 throttling states)
ACPI: Processor [CPU13] (supports 1 throttling states)
ACPI: Processor [CPU33] (supports 1 throttling states)
ACPI: Processor [CPU14] (supports 1 throttling states)
ACPI: Processor [CPU34] (supports 1 throttling states)
ACPI: Processor [CPU15] (supports 1 throttling states)
ACPI: Processor [CPU35] (supports 1 throttling states)
ACPI: Processor [CPU16] (supports 1 throttling states)
ACPI: Processor [CPU36] (supports 1 throttling states)
ACPI: Processor [CPU17] (supports 1 throttling states)
ACPI: Processor [CPU37] (supports 1 throttling states)
ACPI: Processor [CPU18] (supports 1 throttling states)
ACPI: Processor [CPU38] (supports 1 throttling states)
ACPI: Processor [CPU19] (supports 1 throttling states)
ACPI: Processor [CPU39] (supports 1 throttling states)
ACPI: Processor [CPU1A] (supports 1 throttling states)
ACPI: Processor [CPU3A] (supports 1 throttling states)
ACPI: Processor [CPU1B] (supports 1 throttling states)
ACPI: Processor [CPU3B] (supports 1 throttling states)
ACPI: Processor [CPU1C] (supports 1 throttling states)
ACPI: Processor [CPU3C] (supports 1 throttling states)
ACPI: Processor [CPU1D] (supports 1 throttling states)
ACPI: Processor [CPU3D] (supports 1 throttling states)
ACPI: Processor [CPU1E] (supports 1 throttling states)
ACPI: Processor [CPU3E] (supports 1 throttling states)
ACPI: Processor [CPU1F] (supports 1 throttling states)
ACPI: Processor [CPU3F] (supports 1 throttling states)
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:03: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:04: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
brd: module loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
i8042.c: No controller found.
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S5)
Initalizing network drop monitor service
Freeing unused kernel memory: 224k freed
Write protecting the kernel read-only data: 519k
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1a.0 to 64
ehci_hcd 0000:00:1a.0: EHCI Host Controller
ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.0: debug port 2
PCI: cache line size of 32 is not supported by device 0000:00:1a.0
ehci_hcd 0000:00:1a.0: irq 185, io mem 0xbfa02000
ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
GSI 24 sharing vector 0x8A and IRQ 24
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 138
PCI: Setting latency timer of device 0000:00:1d.0 to 64
ehci_hcd 0000:00:1d.0: EHCI Host Controller
ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.0: debug port 2
PCI: cache line size of 32 is not supported by device 0000:00:1d.0
ehci_hcd 0000:00:1d.0: irq 138, io mem 0xbfa01000
ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v3.0
SCSI subsystem initialized
megasas: 06.505.02.00 Wed. Nov. 14 17:00:00 PDT 2012
megasas: 0x1000:0x005b:0x1137:0x008d: bus 1:slot 0:func 0
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 26 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:01:00.0 to 64
gen2: instance->base_addr = bf960000<6>megasas: FW now in Ready state
megasas:IOC Init cmd success
megasas: INIT adapter done
megasas: max_sectors : 0x230, cmd_per_lun : 0x100
scsi0 : LSI SAS based MegaRAID driver
Vendor: LSI Model: MR9265-8i Rev: 3.15
Type: Direct-Access ANSI SCSI revision: 05
Vendor: LSI Model: MR9265-8i Rev: 3.15
Type: Direct-Access ANSI SCSI revision: 05
Vendor: LSI Model: MR9265-8i Rev: 3.15
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 285155328 512-byte hdwr sectors (146000 MB)
sda: Write Protect is off
sda: Mode Sense: 1f 00 00 08
SCSI device sda: drive cache: write back
SCSI device sda: 285155328 512-byte hdwr sectors (146000 MB)
sda: Write Protect is off
sda: Mode Sense: 1f 00 00 08
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
usb 1-1: new high speed USB device using ehci_hcd and address 2
sd 0:2:0:0: Attached scsi disk sda
Vendor: LSI Model: MR9265-8i Rev: 3.15
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 1751949312 512-byte hdwr sectors (896998 MB)
sdb: Write Protect is off
sdb: Mode Sense: 1f 00 00 08
SCSI device sdb: drive cache: write back
SCSI device sdb: 1751949312 512-byte hdwr sectors (896998 MB)
sdb: Write Protect is off
sdb: Mode Sense: 1f 00 00 08
SCSI device sdb: drive cache: write back
sdb: sdb1
sd 0:2:1:0: Attached scsi disk sdb
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Emulex LightPulse Fibre Channel SCSI driver 8.2.0.87.1p
Copyright(c) 2004-2009 Emulex. All rights reserved.
Initializing USB Mass Storage driver...
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 6 ports detected
usb 2-1: new high speed USB device using ehci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 8 ports detected
usb 2-1.3: new high speed USB device using ehci_hcd and address 3
usb 2-1.3: configuration #1 chosen from 1 choice
usb 2-1.4: new full speed USB device using ehci_hcd and address 4
usb 2-1.4: configuration #1 chosen from 1 choice
input: Avocent Cisco USB Composite Device-0 as /class/input/input0
input: USB HID v1.00 Keyboard [Avocent Cisco USB Composite Device-0] on usb-0000:00:1d.0-1.4
input: Avocent Cisco USB Composite Device-0 as /class/input/input1
input: USB HID v1.00 Mouse [Avocent Cisco USB Composite Device-0] on usb-0000:00:1d.0-1.4
input: Avocent Cisco USB Composite Device-0 as /class/input/input2
input: USB HID v1.00 Mouse [Avocent Cisco USB Composite Device-0] on usb-0000:00:1d.0-1.4
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Vendor: UNIGEN Model: PSE4000S3 Rev: PMAP
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdc: 7831552 512-byte hdwr sectors (4010 MB)
sdc: Write Protect is off
sdc: Mode Sense: 23 00 00 00
sdc: assuming drive cache: write through
SCSI device sdc: 7831552 512-byte hdwr sectors (4010 MB)
sdc: Write Protect is off
sdc: Mode Sense: 23 00 00 00
sdc: assuming drive cache: write through
sdc: sdc1
sd 1:0:0:0: Attached scsi removable disk sdc
usb-storage: device scan complete
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.11.5-ioctl (2007-12-12) initialised: dm-devel@redhat.com
device-mapper: dm-raid45: initialized v0.2594l
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
type=1404 audit(1375588399.112:2): selinux=0 auid=4294967295 ses=4294967295
sd 0:2:0:0: Attached scsi generic sg0 type 0
sd 0:2:1:0: Attached scsi generic sg1 type 0
sd 1:0:0:0: Attached scsi generic sg2 type 0
input: PC Speaker as /class/input/input3
iomemory_vsl: module license 'Proprietary' taints kernel.
fioinf VSL configuration hash: d15bf7c78eaf00bf62421df68a96065f0a01516f
fioinf
fioinf Copyright (c) 2006-2013 Fusion-io, Inc. All rights reserved.
fioinf For Terms and Conditions see the License file included
fioinf with this driver package.
fioinf
fioinf ioDrive driver 3.2.3.950 pinnacles@02042bfa64d7 loading...
ACPI: PCI Interrupt 0000:c1:00.0[A] -> GSI 104 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:c1:00.0 to 64
fioinf ioDrive 0000:c1:00.0: mapping controller on BAR 5
fioinf ioDrive 0000:c1:00.0: MSI enabled
fioinf ioDrive 0000:c1:00.0: using MSI interrupts
QLogic 1/10 GbE Converged/Intelligent Ethernet Driver v5.0.7
ACPI: PCI Interrupt 0000:41:00.0[A] -> GSI 56 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:41:00.0 to 64
qlcnic 0000:41:00.0: 2MB memory map
fioinf ioDrive 0000:c1:00.0.0: Starting master controller
QLogic Fibre Channel HBA Driver
GSI 25 sharing vector 0x5B and IRQ 25
ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 91
fioinf ioDrive 0000:c1:00.0.0: SMP Controller Firmware APP version 1.0.8 0
fioinf ioDrive 0000:c1:00.0.0: SMP Controller Firmware BOOT version 1.0.4 1
qlcnic 0000:41:00.0: phy port: 0 switch_mode: 0,
max_tx_q: 1 max_rx_q: 8 min_tx_bw: 0x0,
max_tx_bw: 0x64 max_mtu:0x2580, capabilities: 0xdeeaffae
qlcnic: 00:0e:1e:0b:18:c0 Gigabit Ethernet Board Chip rev 0x58
qlcnic 0000:41:00.0: firmware v4.9.73
qlcnic 0000:41:00.0: phy port: 0 switch_mode: 0,
max_tx_q: 1 max_rx_q: 8 min_tx_bw: 0x0,
max_tx_bw: 0x64 max_mtu:0x2580, capabilities: 0xdeeaffae
qlcnic 0000:41:00.0: using msi-x interrupts
qlcnic 0000:41:00.0: eth0: XGbE port initialized
ACPI: PCI Interrupt 0000:41:00.1[A] -> GSI 56 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:41:00.1 to 64
qlcnic 0000:41:00.1: 2MB memory map
qlcnic 0000:41:00.1: phy port: 1 switch_mode: 0,
max_tx_q: 1 max_rx_q: 8 min_tx_bw: 0x0,
max_tx_bw: 0x64 max_mtu:0x2580, capabilities: 0xdeeaffae
qlcnic 0000:41:00.1: firmware v4.9.73
qlcnic 0000:41:00.1: phy port: 1 switch_mode: 0,
max_tx_q: 1 max_rx_q: 8 min_tx_bw: 0x0,
max_tx_bw: 0x64 max_mtu:0x2580, capabilities: 0xdeeaffae
qlcnic 0000:41:00.1: using msi-x interrupts
qlcnic 0000:41:00.1: eth1: XGbE port initialized
ACPI: PCI Interrupt 0000:41:00.6[A] -> GSI 56 (level, low) -> IRQ 209
qla2xxx 0000:41:00.6: Found an ISP8021, irq 209, iobase 0xffffc200109bf000
qla2xxx 0000:41:00.6: Configuring PCI space...
PCI: Setting latency timer of device 0000:41:00.6 to 64
fioinf ioDrive 0000:c1:00.0.0: Required PCIE bandwidth 2.000 GBytes per sec
fioinf ioDrive 0000:c1:00.0.0: Board serial number is 1244D13EB
fioinf ioDrive 0000:c1:00.0.0: Default capacity 365.000 GBytes
fioinf ioDrive 0000:c1:00.0.0: Default sector size 512 bytes
fioinf ioDrive 0000:c1:00.0.0: Rated endurance 4.00 PBytes
fioinf ioDrive 0000:c1:00.0.0: 100C temp range hardware found
fioinf ioDrive 0000:c1:00.0.0: Maximum capacity 395.000 GBytes
fioinf ioDrive 0000:c1:00.0.0: Firmware version 7.1.13 109322 (0x70040d 0x1ab0a)
fioinf ioDrive 0000:c1:00.0.0: Firmware VCS version 109322 [0x1ab0a]
fioinf ioDrive 0000:c1:00.0.0: Firmware VCS uid 0x02a0b00fd435f92c3cebbf431f69bd563a77cfe3
fioinf ioDrive 0000:c1:00.0.0: Powercut flush: Enabled
fioinf ioDrive 0000:c1:00.0.0: Thermal monitoring: Enabled
fioinf ioDrive 0000:c1:00.0.0: Hardware temperature alarm set for 100C.
fioinf ioDrive 0000:c1:00.0: Found device fct0 (Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0) on pipeline 0
qla2xxx 0000:41:00.6: Configure NVRAM parameters...
qla2xxx 0000:41:00.6: Verifying loaded RISC code...
qla2xxx 0000:41:00.6: qla82xx_set_drv_active(2): drv_active = 0x11
qla2xxx 0000:41:00.6: 1:Device state is 0x3 = Ready
qla2xxx 0000:41:00.6: 2:Device state is 0x3 = Ready
scsi2 : qla2xxx
qla2xxx 0000:41:00.6:
QLogic Fibre Channel HBA Driver: 8.03.01.05.05.06-k
QLogic QMC8242 - Cisco UCS CNA M73KR-QLogic
ISP8021: PCIe (2.5Gb/s x8) @ 0000:41:00.6 hdma+, host#=2, fw=4.09.73 (804)
ACPI: PCI Interrupt 0000:41:00.7[A] -> GSI 56 (level, low) -> IRQ 209
qla2xxx 0000:41:00.7: Found an ISP8021, irq 209, iobase 0xffffc200118bf800
qla2xxx 0000:41:00.7: Configuring PCI space...
PCI: Setting latency timer of device 0000:41:00.7 to 64
fioinf Waiting for /dev/fct0 to be created
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: probed fct0
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: sector_size=512
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: setting channel range data to [2 .. 2047]
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: ***************************************************
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: *** unclean shutdown detected, re-scanning log. ***
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: *** this may take several minutes. ***
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: ***************************************************
qla2xxx 0000:41:00.7: Configure NVRAM parameters...
qla2xxx 0000:41:00.7: Verifying loaded RISC code...
qla2xxx 0000:41:00.7: qla82xx_set_drv_active(3): drv_active = 0x1000011
qla2xxx 0000:41:00.7: 1:Device state is 0x3 = Ready
qla2xxx 0000:41:00.7: 2:Device state is 0x3 = Ready
scsi3 : qla2xxx
qla2xxx 0000:41:00.7:
QLogic Fibre Channel HBA Driver: 8.03.01.05.05.06-k
QLogic QMC8242 - Cisco UCS CNA M73KR-QLogic
ISP8021: PCIe (2.5Gb/s x8) @ 0000:41:00.7 hdma+, host#=3, fw=4.09.73 (804)
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: Successfully reattached after unclean shutdown. (AP: 339+228114432)
fioinf enable_discard set but discard not supported on this linux version
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: Creating block device fioa: major: 252 minor: 0 sector size: 512...
fioa: fioa1
fioinf Waiting for /dev/fioa to be created
fioinf Cisco UCS 365GB MLC Fusion-io ioDrive2 0000:c1:00.0: Attach succeeded.
floppy0: no floppy controllers found
work still pending
lp: driver loaded but no devices found
mtrr: type mismatch for be000000,400000 old: write-back new: write-combining
mtrr: type mismatch for be000000,1000000 old: write-back new: write-combining
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Mapper loaded
dell-wmi: No known WMI GUID found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on sda2, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
EXT4-fs (sdb1): mounted filesystem with ordered data mode
EXT4-fs (fioa1): mounted filesystem with ordered data mode
Adding 104412k swap on /dev/sda3. Priority:-1 extents:1 across:104412k
Loading iSCSI transport class v2.0-871.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
cxgb3i: tag itt 0x1fff, 13 bits, age 0xf, 4 bits.
iscsi: registered transport (cxgb3i)
IPv6: Loaded, but administratively disabled, reboot required to enable
Broadcom NetXtreme II CNIC Driver cnic v2.1.2 (May 26, 2010)
Broadcom NetXtreme II iSCSI Driver bnx2i v2.1.3 (Aug 10, 2010)
iscsi: registered transport (bnx2i)
iscsi: registered transport (tcp)
iscsi: registered transport (iser)
iscsi: registered transport (be2iscsi)
qlcnic 0000:41:00.0: NIC Link is up
qlcnic 0000:41:00.0: NIC Link is down
qlcnic 0000:41:00.1: NIC Link is up
qlcnic 0000:41:00.1: NIC Link is down
qlcnic 0000:41:00.0: NIC Link is up
qlcnic 0000:41:00.1: NIC Link is up
mtrr: type mismatch for be000000,400000 old: write-back new: write-combining
mtrr: type mismatch for be000000,1000000 old: write-back new: write-combining
FS-Cache: Loaded
qlcnic 0000:41:00.0: NIC Link is up
qlcnic 0000:41:00.1: NIC Link is up
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
mtrr: type mismatch for be000000,400000 old: write-back new: write-combining
mtrr: type mismatch for be000000,1000000 old: write-back new: write-combining
loop: loaded (max 8 devices)
Subscribe to:
Posts (Atom)